Charging With The 12V Motor Vehicle; Charging Cable; Starter Aid; Onnecting The Power Pack - EAL APA 16540 Manuel De L'opérateur

The control LED (position 5 in the overview) is now red.
For the initial charging process, leave the power pack
connected for 24 hours. For all subsequent charging
processes or directly after use charge no longer than
20 hours. Once the battery is fully charged, the LED is
green. After the charging process, fi rst pull out the plug-
in charger from the socket and then unplug the coaxial
power connector from the charging socket of the power
pack. Now close the charging socket with the sealing
plug. If you press the battery test switch now, the control
LED is green.

6.2.2 CHARGING WITH THE 12V MOTOR VEHICLE

CHARGING CABLE

Turn the on-off switch (position 1 in the overview) to
the OFF position. Plug the coaxial power connector of
the cigarette lighter charging cable (position 12 in the
overview) into the charging socket of the power pack
(position 6 in the overview). Now plug the 12V vehicle
plug into the 12V socket of your vehicle. The control LED
(position 5 in the overview) is now red. Charge the power
pack for approx. 6 – 8 hours.
CAUTION
Only charge the power pack while
driving or when the engine is running,
otherwise there is a risk of discharging
the starter battery of your vehicle.
Once the battery is fully charged, the LED is green. After
the charging process, fi rst pull out the 12V vehicle plug
from the socket of your vehicle and then unplug the
coaxial power connector from the charging socket of
the power pack. Now close the charging socket with the
sealing plug. If you press the battery test switch now, the
control LED is green.

6.3 STARTER AID

Make sure that the power pack is fully charged. To do so,
press the battery test switch (position 4 in the overview).
Once the control LED is green (position 5 in the overview),
the power pack is ready for use.
The starter aid function of the power
pack is only for vehicles with 12 V on-
board voltage. Before you start, read the
operating instructions of your vehicle, if
and how and external starter aid can be
used. Modern vehicles have sensitive
electronics and control devices that can
be damaged when handled incorrectly.
6.3.1 CONNECTING THE POWER PACK

(VEHICLES WITH NEGATIVE EARTH)

Turn off the ignition of your vehicle as well as all electrical
consumers (radio, light, rear window heating, seat
heaters, etc.). Enable the parking brake.
Turn the on-off switch (position 1 in the overview) to the
OFF position. First connect the red (+) terminal clamp
(position 11 in the overview) to the positive terminal of
your vehicle battery. Connect the black (-) terminal clamp
(position 10 in the overview) as far away from the battery
as possible to the engine block or chassis (no painted parts).
If the power pack is properly connected, the reverse polarity
protection view is lit green (position 2 in the overview). If
this is not the case, the reverse polarity protection view is lit
red and a warning signal is sounded. In this case, check the
connection of the terminal clamps and correct it. Now turn
the on-off switch to the ON position.

6.3.2 START ATTEMPT

Start the engine. Do not let the starter motor work longer
than 6 s. The battery of the power pack is not suitable for
longer start attempts. Between start attempts, take a
break of at least 5 minutes. If the engine doesn't turn on
after several attempts, discontinue using the starter aid
and look for the cause of the malfunction.

6.3.3 REMOVING THE POWER PACK

Now turn the on-off switch to the OFF position. First
remove the black (-) terminal clamp, roll up the cable
and fasten the terminal clamp to its designated holder.
Then remove the red (+) terminal clamp, roll up the cable
and fasten the terminal clamp to its designated holder.
Always adhere to this sequence.
Recharge the power pack.

6.4 COMPRESSOR

In order to be able to work with the compressor, fi rst take
the air hose (position 7 in the overview) out of the holder.
To do so, you briefl y have to remove the red (+) terminal
clamp from its holder.

6.4.1 FILLING A TYRE WITH THE CAR

VALVE / SCHRADER VALVE

Öffnen Sie die
Verriegelung
Open the lock on
am Ventilanschluß
the valve connector
Fig. 2
Setzen Sie den
Ventilanschluß auf
Place the valve
das Ventil
connector on the valve
Fig. 3
9
Ve
Ve