Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
OPERATION
WARNING: Always wear eye protection, ade-
quate respiratory and hearing protection, as
well as suitable gloves, when working with this
tool.
Switching on and off
1.
Ensure the trimmer head is in the correct
mode.
2.
Pick up the trimmer; hold the machine
with one hand on the Main Handle (3) and
the other on the Auxiliary Handle (1). The
handle is equipped with an integrated
Safety Lock-Off (2).
3.
Switch on the machine by pressing the
Safety Lock-Off and then the On/Off Trig-
ger (4). The machine will run until the On/
Off Trigger is released.
Grass trimming
1.
Always keep the machine at arm's length
with the trimmer head pointed away from
your body.
2.
Move the trimmer head across the area to
be trimmed using a smooth sweeping
motion.
3.
When approaching an edge or wall, try to
avoid allowing the line to impact the wall or
any other hard vertical surface.
Lawn edging
WARNING: Be careful when lawn edging as
any excess line cut off will be removed on a
vertical axis and if the tool is tilted it is possible
it could be thrown towards the operator's eyes.
1.
Put the tool into lawn edging mode with
the Mode Selector (15).
2.
Turn the tool over so the Edging Small
Roller (13) and Edging Large Roller (14)
are on the ground and position on the
edge of the lawn.
3.
Carefully move the tool along, trimming
only the excess grass over the edge of the
earth below.
Feeding the trimmer line
•
When the trimmer line becomes too short,
bump the spool housing quickly and gen-
tly against the ground while de machine is
running and the spool will release more
trimmer line.
10
MAINTENANCE AND CLEANING
WARNING: Always disconnect from the mains
power supply, before carrying out any mainte-
nance/ cleaning of the charger. Remove the
battery before carrying out any maintenance/
cleaning of the tool.
Maintenance
There are no inner parts of the tool which need
maintenance.
Cleaning
•
Keep safety devices, ventilation openings
and the motor housing as free as possible
from dirt and dust. Rub the electric power
tool with a clean cloth or blow over it with
low pressure compressed air.
•
We recommend that you clean your elec-
tric power tool immediately after each use.
•
Clean the electric power tool regularly with
a damp cloth and somewhat soft soap. Do
not use any cleaning or solvent materials;
these can attack the device's plastic com-
ponents. Make sure that no water can get
inside the electric power tool.
TECHNICAL DATA
No Load Speed. . . . . . . . . . . 8000 min
Trimming Diameter . . . . . . . . . . 230 mm
Dimensions . . . . . . . . . 155 × 24 × 19 cm
Weight . . . . . . . . . . . . . . . . . 2.3 kg
Sound Pressure Level L
. . . . 72.40 dB(A)
pA
Uncertainty K
. . . . . . . . . . . . . . 3 dB
pA
Sound Power Level L
. . . . . .87.37 dB(A)
WA
Uncertainty K
. . . . . . . . . . . . . . 3 dB
WA
Hand Arm Vibration
Main handle . . . . . . . . . . . 6.531 m/s
Auxiliary handle . . . . . . . . . 6.764 m/s
Uncertainty K . . . . . . . . . . . . . .1.5m/s
DISPOSAL
Do not dispose of electric power
tools with domestic refuse.
The electric power tool is shipped in
packaging to reduce transport damage. This
packaging is a raw material and as such can
either be reused or can be fed back into the
raw material cycle. The electric power tool and
its accessories are made from various materi-
als such as metals and plastics. Take defective
components to a special refuse collection
point. Ask about these at your specialist shop
or local council. The product and the user
manual may be subject to changes. Technical
data may be changed without prior notice.
Batteries
Think of the environment when disposing of
batteries. Contact your local authorities to find
out where your nearest disposal area is.
Do not dispose of batteries with domestic
refuse.
Do not dispose of by burning, risk of explosion.
-1
2
2
2
English
EC-DECLARATION OF CONFORMITY
We, the Batavia GmbH, Weth. Buitenhuis-
straat 2a, NL-7951 SM Staphorst, declare by
our own responsibility that the product Cord-
less grass trimmer, Model BT-CLT001,
Item-No 7062515 is according to the basic
requirements, which are defined in the Euro-
pean Directives Electromagnetic Compatibility
2014/30/EU (EMC), 2006/42/EC (Machinery),
2011/65/EU (RoHS), 2000/14/EU and their
amendments. For the evaluation of conformity,
the following harmonized standards were
consulted:
EN60335-1
EN62233
EN50636-2-91
EN55014-1
EN55014-2
Staphorst, 24 March 2017
Meino Seinen, QA Representative
Batavia GmbH, Weth. Buitenhuisstraat 2a,
7951 SM Staphorst, Netherlands
11
Publicité
Table des Matières
