Maintenance And Service; Maintenance And Cleaning - Bosch GRW 9 Professional Notice Originale

Masquer les pouces Voir aussi pour GRW 9 Professional:

Notice originale (8 pages)

Table Des Matières

100

101

102

103

104

105

106

107

108

109

110

111

112

page de 112

/ 112
Matières
Table des Matières
Signets

Table des Matières

Les langues disponibles

OBJ_BUCH-322-002.book Page 10 Wednesday, January 18, 2012 8:33 AM

10 | English

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under "Technical Data" is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider

Dr. Eckerhard Strötgen

Senior Vice President

Engineering Director

Engineering

PT/ESI

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

16.12.2011

Assembly

Before any work on the machine itself, pull the mains

plug.

Splash Guard / Auxiliary Handle

The splash guard 4 protects the machine against contamina-

tion and is used for fastening the auxiliary handle 7. Slide the

splash guard 4 onto the spindle collar and then tighten the

clamping nut 9.

Insert the auxiliary handle 7 into the drill hole of the splash

guard 4, turn the auxiliary handle 7 to the requested positon

and lock it by shutting the clamping lever 8.

Changing the Tool

Stirrer Paddle with Male Thread, Size M 14 (see figure A)

Screw the stirrer paddle 1 with the adapter 2 onto the drive

spindle 3. Hold the drive spindle 3 in place with an open-end

spanner (size 22 mm) and tighten the adapter 2 and the stir-

rer paddle 1 with a second open-end spanner (size 22 mm).

The stirrer paddle is disassembled in reverse order.

Stirrer Paddle with External Hexagon

Screw the stirrer paddle 1 directly onto the drive spindle 3.

Hold the drive spindle 3 in place using a open-end spanner

(size 22 mm) and, using a second open-end wrench (size

22 mm), tighten the stirrer paddle 1.

The stirrer paddle is disassembled in reverse order.

Operation

Starting Operation

Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

3 609 929 C35 | (18.1.12)

Dusts, e. g. mineral dusts, can be harmful to one's health.

Contact with or inhaling the dusts can trigger allergic reac-

tions to the operator or bystanders and/or lead to respira-

tory infections.

Materials containing asbestos may only be worked on by

specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Switching On and Off

To start the machine, press the On/Off switch 6 and keep it

pressed.

Lock the pushed On/Off switch 6

by pushing the lock-on button 5 up-

ward.

To switch off the machine, release the On/Off switch 6 or

when it is locked with the lock-on button 5, briefly press the

On/Off switch 6 and then release it.

Working Advice

The choice of stirrer paddle depends on the material to be

stirred. For materials with low viscosity, e. g., dispersion

paint, varnish, adhesions, casting compound, cement grout,

etc., use a stirrer paddle with left-hand spiral.

For materials with high viscosity, e. g., ready-mixed plaster,

concrete, cement, screed, filler, epoxy resin, etc., use a stir-

rer paddle with right-hand spiral.

While mixing, move the power tool in an up and down motion.

Clean the stirror paddle after use.

Avoid splashing around the material being stirred. Oth-

erwise, you could slip and lose control over the power tool.