THOMSON T24RTE1021 Mode D'emploi page 7

4. Getting started – installing the batteries
Note
• Alkaline batteries recommended. Please
use 2 "AAA" (LR03/Micro) type batteries.
• Remove the battery cover from bottom of
remote. (A)
• Check the +/- polarity on the batteries
and inside the battery compartment.
• Insert the batteries. (B)
• Slide the battery holder back into the
remote until the clips locate. (C)
When exchanging the batteries, it may
be necessary to reprogram the unit.
Hence it is advisable to record the
codes needed for your devices.
5. Settings of the remote control
5.1 Default setting/factory setting
This remote control comes factory preset.
When the batteries have been inserted most of
the devices of the brands Haier, Mitsubishi and
Toshiba can be controlled. For other brands
please use one of the following methods, A, B,
C or D, for programming.
5.2 Method A – Topspeed searching of brands
Please take a look to the remote, each key has
a brand over or under the key. These are the
brands preprogrammed on each key to help
you to set up your remote with only one key.
For example: the "TEMP" ▲ key is for LG and
Samsung.
• Manually turn on the air conditioner, and
point the remote control towards the
reception window of the air conditioner.
• Press the key corresponding to your air
conditioner brand until the air conditioner
automatically activates with a "beep" sound.
5.3 Method B – Fully automatic search
applicable model
• Manually switch on the air conditioner and
point the remote control to the receiving
window of the air conditioner.
• Keep pressing the "Set" button for about 6
seconds. Carefully observe the status of the
air conditioner when the model code " – "
ickers the window. Only release the button
when the air conditioner starts automatically.
• Check whether the button function is correct.
If yes, the code would be valid. If not, please
repeat the step 2-3.
Note
If you could not switch on the device
manually, repeat steps 1 to 3 with the
device switched off. Some brands accept
the code searching but the process could
take up to 5 min.
5.4 Method C – Manual code inputting
method
• Manually switch on the air conditioner, nd
the model corresponding to the air condi-
tioner you are about to control remotely in
"Code List" and nd the rst group of codes.
• Firstly keep pressing "Set" button and then
press "Power" button at the same time.
Don't release the two buttons until the
model code ickers in the window. Then
press "Temp ▲" button until the code
needed is shown in the window and ickers.
The air conditioner will automatically start if
the code is correct.
• Check whether the function of the various
buttons is correct. If yes, the setting is
nished. If not, please repeat step 2-3.
5.5 Method D – Manual code searching
method
• Manually switch on the air conditioner and
point the remote control to the receiving
window of the air conditioner.
• Firstly keep pressing "Set" button and press
"Power" button at the same time. Do not
release them when the model code ickers
in the window. Then press "Temp ▲" button
and carefully observe the status of your air
conditioner. Press "Set" button for exit when
the air conditioner automatically starts.
6. Reset to default
Restore factory settings: synchronously press
"Set"" + "Wind
then factory settings restoring is done.
7. Special functions
7.1 Rapid cooling and rapid heating button
• Press "COOL" (fast cooling) button to auto-
matically set the cooling mode : 21°C, strong
breeze, automatic wind.
• Press "HEAT" (fast heating) button to
automatically set the heating mode : 27°C,
strong breeze, automatic wind.
Note
Under the heating mode, press "HEATING"
(Electric Auxiliary Heating) button to start
the electric heating function. This function
is only available if the air conditioner has a
heating function.
2
" button for 3 seconds and