Publicité
Connecting Transmitter to your Music Player
The Transmitter can use the following kinds of music players
•
as a music source: CD, DVD, MP3, or MP4.
The sound for the heater speaker is influenced by the source
sound. Generally speaking, high-power and high-quality music
source can make a louder and clearer sound from the heater
speaker.
Use a connection wire equipped with a 3.5mm headphone
•
jack to connect the Transmitter to your Music Player. We have
included a Transmitter Wire (with 3.5mm headphone jack) for
your convenience.
Turn the Transmitter Battery Power Switch ON. Make sure your
•
Music Player is ON.
Connecting Transmitter to your Computer
Your computer can be used as a music and power source
•
for the Transmitter. Connect a USB 2.0 cable to the USB ports
on the Transmitter and your Computer. (A USB Connection
Wire has been included for your convenience.) Make sure the
Battery Power Switch is turned OFF and that your computer
has adequate power.
The Transmitter system is compatible with Windows 98SE/
•
ME/2000/XP/Vista and Mac OSX without the use of an
additional driver.
Item # 42
Transmitter
Transmitter Wire
Item # 41
Item # 53
Transmitter
USB Connection Wire
Item # 41
Pairing the System with Transmitter
Make sure the Transmitter is plugged into Music Source (If
•
using battery power, make sure the Transmitter Battery Switch
is turned ON). Turn the Music Source on and set to PLAY.
Push the right knob on Totum (about 1-3 seconds); this will
make the Totum's Music and Light System go into automatic
Pairing mode. Pairing Mode will last 20 seconds. If Pairing
is successful, the Totum Music and Light System will sync.
Music will play out of the speakers, and the lights will flash
to the beat of the music.
If pairing is unsuccessful, the Music and Light System will
•
shut off automatically. Use the steps below to pair the System
manually:
Press and hold the ID Button on the Transmitter and the
1.
Right Knob on the Totum. Hold both buttons down for
more than 5 seconds.
EN
O P E R A T I O N
•
Music Source
Computer
Music Source
8
The light bars on the sides of the Totum will be solid
2.
white.
Successful Pairing will be indicated by a single BEEP.
3.
If Pairing fails, turn off transmitter and the right knob and
4.
retry.
Pairing only has to be performed once with a new system
or additional Totums.
Up to 50 Totums can be controlled at the same time by one
•
Transmitter. The Totum(s) must be within 82 feet (25 meters)
of the Transmitter for pairing.
To Turn Music and Light System ON/OFF:
To turn Lights ON: Push the right knob (about 1-3 seconds).
•
The light bars turn green.
With your music source plugged into the Transmitter, turn
•
Transmitter power on.
To turn Lights OFF: Push the right knob again (about 1-3
•
seconds). The light bars turn Blue.
To Turn Light Sync Feature OFF During
Music Play:
Turn the right knob to scroll through available colors for
•
the light bars and stop until the desired color is reached.
There are 11 colors to choose for the Light Bars. The light
bars will remain static (no flashing) in the color of your
choice.
If you want to turn OFF the Light Bars, turn the right knob
•
and stop the light off.
Once light sync mode has been turned OFF, the system
•
must be restarted (power OFF then ON) to enable light sync
again.
Sleep Mode:
If the music stops in Light Sync mode, the Music and
•
Lights System will turn OFF and go into Sleep Mode
after 5 minutes. Press PLAY on your Music Source to
exit Sleep Mode.
Charging the battery
If the battery is on low power, the light bars on the heater
turn red, signaling you to charge the battery.
During the charging, the indicator light on the charger is red
when the charging is completed the indicator light on the
charger will turn green. After every charging, the battery can
be used up to 6 hours.
Indicator Light
Item # 55
Item # 56
Publicité
