Dörr SCL-18042 Notice D'utilisation page 7

03 | PRODUCT DESCRIPTION
Multifunctional LED Zoom torch for security and outdoor requirements with
charging base.
Max. 750 Lumen with a beam distance of about 150 m
•
Robust and shockproof aluminum housing
•
Water resistant according to protection class IPX4 (splash-proof)
•
Various light functions (flashing, SOS)
•
Supplied with long-life Li-Ion battery, charging base and wall mount
•
Including USB cable and power adapter
•
04 | NOMENCLATURE
01 Zoom light head
02 Rotating ring (cover Micro USB port)
03 Micro USB port
04 Illuminated ring red/green (charging status)
05 Screw cap battery compartment
06 On/Off button
07 Charging slot
08 Illuminated ring blue (ready light)
09 Micro USB port
10 Suspensions for wall mount
11 Power adapter
12 USB port
13 USB cable
14 Wall mount
15 Drill holes
16 Hooks
05 | OPERATION
05.1 INSERTING THE LI-ION BATTERY
Screw-off the screw cap (5) counter clockwise. Insert the supplied Li-Ion battery
type WT21700 into the battery compartment and screw on the screw cap again.
NOTE
The supplied Li-Ion battery type WT21700 is equipped with each one positive
and negative pole at both sides. Thus it can be inserted in any direction.
05.2 CHARGING THE LI-ION BATTERY
Before first use, please fully charge the Li-Ion battery. There are two options to
charge the battery:
05.2.1 CHARGING VIA CHARGING BASE
To charge the battery via the charging base, first connect the USB cable (13) to
the Micro USB port at the charging station (9) and with the USB port (12) of power
adapter (11). Plug the power adapter (11) into a power outlet. The illuminated ring
(8) at the charging base lights up blue.
Place the torch in the charging slot (7). The illuminated ring (4) at the torch lights up
red while charging. After about 4.5 hours, the Li-Ion battery is fully charged and the
illuminated ring (4) at the torch turns green.
05.2.2 CHARGING VIA MICRO USB PORT
Turn down the rotating ring (2) counter clockwise. The Micro USB port (3) is located
underneath. Connect the torch to the power adapter (11) using the supplied USB
cable (13). Plug the power adapter (11) into a power outlet.
Alternatively connect the torch to your computer using the supplied USB cable (13).
In this case, the charging time will be extended.
After charging remove the Micro USB cable and turn up the rotating ring (2)
clockwise to cover the Micro USB port and to ensure the water resistance.
05.3 FUNCTIONS OF THE TORCH
To switch on the torch and to select the various light functions, press the On/Off
button (6) as follows:
Switching on
Medium
Low power
Full power power
150 Lumen
750 Lumen 300 Lumen
press 1x press 2x
NOTE
If the torch is on for at least 5 seconds in one mode, it can be switched off
immediately by pressing the on/off button once.
To zoom the light beam, slide the light head (1) forward.
ATTENTION: During the operation the aluminum housing will warm up.
06 | WALL MOUNT
With the supplied wall mount (14) you can mount the charging station to the wall:
Screw the wall mount through the two drill holes (15) to the wall and hang the
charging station with the two hooks (16) into the suspensions (10) of wall mount.
07 | CLEANING AND STORAGE
Never use aggressive cleansing agents or benzine to clean the device. We recom-
mend a soft, slightly damp microfiber cloth to clean the outer parts of the device.
Make sure to take off the device from power before cleaning! Store the device in
a dust-free, dry and cool place. This device is not a toy - keep it out of reach of
children. Keep away from pets.
07
Flashing
SOS light
light
press 3x press 4x press 5x
Switching
off
press 6x