Aurora 777 Mode D'emploi page 5

Also it shouldn't be possible to touch the knobs by a person in the bath or in the
shower.
3. Wall mounting (for wall mountable versiones only)
Remove the bracket by pushing it towards the product (1), pressing from the high on
the undulated area using a screw driver (2) and then pulling it out (3);
Make sure that the minimum distances from walls, floor and ceiling are respected
according to fig. 2.
Drill the holes on the wall using the wall bracket as a frame, insert the rawplugs and
fix the wall bracket firmly with 2 screws as shown in fig. 3.
Hang the heater to the wall bracket, pressing it onto the bracket until you hear a
"click".
Note that the heater can be oriented in different positions, rotating on the wall bracket
as shown in fig. 4.
In case you want to remove the heater from the wall, place it in the central position,
push the product towards the wall, press with a screwdriver over the bracket as
shown in fig. 5. and pull it out.
4. Cord storage
For product recovery you can store the cordset pressing it into the product.
Mind that during function the cordset must be always completely pulled out.
5. Use of the heater
The heater has 2 knobs: one controles the switch and the other the thermostat.
The switch knob has 5 positions, allowing to select the desired
power setting :
= COLD AIR: only the fan works
O
= OFF
= WARM AIR at reduced motor speed (QUIET MODE 1000W)
= WARM AIR at full motor speed (1200W)
= HOT AIR at full motor speed (2000 W)
The pilot light will switch on during heater functioning (version with pilot light only)
independently from thermostat regulation.
Starting from the " " position, turn the thermostat knob clockwise until you hear a
"click»: the appliance starts working at the desired power setting.
The thermostat maintains the desired room temperature switching on and off
automatically the appliance. The more the knob is turned clockwise, the higher is the
maintained temperature. Maximum thermostat setting corresponds at about 30° C;
" " position corresponds to approximately 5° C.
Use of the thermostat
In a room where the temperature is too high (more than 30° C), it is normal that the
thermostat will not switch on the heater.
In a room where the temperature is too low (around 5° C or even less) it is also
normal that the thermostat will keep the appliance working until the temperature gets
higher.
To select the right thermostat position we suggest you to
- turn the thermostat in maximum position (clockwise);
- leave the appliance working until the comfortable temperature is reached;
- turn the knob anti clockwise until you hear a "click" and the appliance stops;
- turn clockwise again the knob (just a little): in this position the thermostat will
maintain the comfortable temperature you have selected.
6. Safety in case of abnormal operation
In case of overheating the safety cut out protecting the heating element will
automatically switch off the appliance.
In this case the appliance stops working and the pilot light will remain switched on
even if the appliance is not working.
If this happens:
- switch off the fan heater;
- remove the causes of abnormal operation or overheating (i.e. obstacles in front of
air inlet or air outlet grille);
- leave the heater cool down for 15/20 minutes;
- switch on again the fan heater.
7. Maintenance
This fan heater does not require any particular maintenance.
We only recommend to clean at least twice a year the air inlet and air outlet grille
with a vacuum cleaner to remove dust from motor and heating element.
In case you need to repair it, please contact an authorised repairing center.
If the cordset is to be changed, please mind that a 2x1mm
to be used.
NEDERLANDS
INSTRUCTIES VOOR HET GEBRUIK
1. Voor uw veiligheid
Deze warmeluchtventilator is een bijkomende verwarmingsbron en dient uitsluitend
voor dit doel gebruikt te worden.
Kijkt u na of de netvoeding overeenkomt met de gegevens op het plaatje: 230V AC,
50Hz.
Verlaat u uw woning nooit terwijl de warmeluchtventilator in werking is. Controleer in
dat geval altijd of de schakelaar op OFF (0) staat en of de thermostaat op de
minimumstand staat (*).
Tijdens de werking zet u de warmeluchtventilator op een veilige plaats, dus:
- op minstens 1 m van ontvlambare of mobiele objecten;
- in geval van bevestiging aan de muur, niet aan plastic of synthetische muren;
- de luchtinlaat- en luchtuitlaatroosters moeten vrijgelaten worden: er mogen zich
in geen geval objecten binnen een straal van 1 m. van het luchtuitlaatrooster
bevinden en binnen een straal van 50 cm. van het rooster aan de achterkant;
- nooit onmiddellijk onder een stopcontact.
2
H05VVF HAR cordset is