Elcoman KOBRA 245TS Mode D'emploi page 10

FEATURES
The KOBRA 245TS, 260TS, 270TS, 310TS, is suitable for
shredding single, and computer printouts as well as
CDROMS/DVDS and CREDIT CARDS.
INSTALLATION FIg.1
For machines with a removable plug, use an easily accessible
power socket near the machine.
-KOBRA 245TS/260TS Fig.1
Once the machine has been taken out of its packaging,
position the head of the machine (A) on the cabinet (B).Open
the door (C) and slide the bag frame (D) off its tracks (E).
Fit the plastic bag (F) which comes with the shredder to the
bag frame (D) then slide it back onto the track (E) in fully,
position the container for shredded CD/DVD/CREDIT CARD
particles (12) on the inside of the door and shut the door
again (245TS models are not equipped with cutting blades
for shredding CD/DVD/CREDIT CARDS and a separate
particle collection bin (12).
-KOBRA 270TS/KOBRA 310TS Fig.2
Once the machine has been taken out of its packaging,
position the head of the machine (G) on the cabinet (H).
Open the door (I) and remove the bag frame (M). Fit the
plastic bag (N) which comes with the shredder to the bag
frame (M) then slide it back onto the track (L). Push the bag
frame (L) in as far as it will go and close the door (I).
The KOBRA 270TS and 310TS (HS models axcluded) are
supplied with a canvas bag for the separate collection of
shredded CD/DVD/CREDIT CARD particles
CONTROLS wITH TOUCH SCREEN TECNOLOgy
All shredders in the KOBRA 245TS, 260TS,270TS and 310TS
range come with TOUCH SCREEN tecnology. Machine
functions are activated by simply touching the respective
button on the control panel.
- FORWARD: Simply touch the FORWARD button and the
cutting blades operate in the forward direction.
Leave your finger on the button for 7 seconds and the
machine carries out a 30 second shredding cycle making
it possible to shred trasparent material witch would not
automatically start the machine since it is invisible to the
electronic eyes.
- STOP: Touch the STOP button and the machine stops
Instantly.
- REVERSE: Touch the REVERSE button and the cutting
blades go into reverse.
- OIL: (KOBRA270TS/310TS) Touch the OIL button and the
light (5) goes off after manual lubrification. Or signals that
oil is low if the machine is equipped with the AUTOMATIC
OILER system
USINg THE MACHINE FIg.3
Once the machine has been plugged in to the mains,press
the ON/OFF button (O),the bar (P) on the control panel
lights up and machine is ready for use.If the machine is then
not used for 8 seconds, the bar(P) goes off and the machine
is put on stand-by with zero power consumption and the
ENERGY SMART light(1) comes on.
As soon as any material to be shredded is introduced into
the throad,the machine comes on again automatically.If the
machin is not used for 4 hours,it switches off automatically
from the mains power supply and the ENERGY SMART light
(1) goes off To switch the machine back on press the ON/
OFF button (O)
SHREDDINg SINgLE SHEETS OF PAPER (FIg. 3)
(A COMMON FUNCTION OF ALL THE KOBRA 245TS/260TS/
270TS AND 310TS).
When sheets of paper are inserted into the throat (2),the light
bar (P) comes on (if off) and the machine begins shredding
automatically thanks to two electronic eyes (3) located on the
inside of the throat which detect the throughput of sheets of
paper and automatically stop the cutting blades a few seconds
after shredding is finished.
The machine is fitted with a LOAD METER (4) which allows you
to monitor the load capacity of your machine ( 270TS, 310TS).
When paper is inserted into the throat (2),the lights (4) come
on.
The sequence in which the lights (4) come on depends on the
amount of paper inserted into the machine. In order to ensure
optimum shredding,we recommend only the first 4 blue lights
be it up on the LOAD METER (4). If the paper load increases,the
rest of the lights come on,first the yellow lights, then the red
lights to indicate a paper jam. If the amount of paper inserted
axceeds the load capacity of the machine,the shredder cuts out
and the am warning light (8) comes on.
The machine then automatically goes into reverse for a few
seconds to free up the cutting blades and stops. Remove the
excess paper from the throat (2) to free the electronic eyes (3)
and then insert a smaller amount of paper into the throat and
the machine automatically starts a new shredding cycle.
It is recommended to limit jams caused by insertion of axcessive
quantities of paper and to operate the machine below its
maximum shredding capacity in order to prolong the life of the
mechanical parts and the machine itself.
(KOBRA 270TS, 310TS)
All models come with warning lights (5) to tell the operator
when the cutting blades need to be oiled.Just shred a sheet of
paper sprinkled with the KOBRA oil supplied with the machine.
Then press the OIL button (6) to switch off the warning light (5).
Now your shredder is oiled.
For models with the built-in oiling system AUTOMATIC
OILER,the warning light (5) flashes when the oil container is
empty and in this case the empty container must be replaced
with a full one.(SEE ACCESSORIES).
About one minute after the replacement of the oil container
the OIL ligth (5) will switch off automatically.
SHREDDINg CD/DVD/CREDIT CARDS
Insert the optical media into the throat of the machine (2A),the
light bar (P) comes on and the machine starts up automatically
thanks to the electronic eyes located on the inside of the throat
(2A) which detect the presence of material to be shredded and
automatically stop the cutting blades a few seconds after
shredding is finished.
The machine is fitted with a special bin (12) or (12A) for
collecting the particles of CD/DVD/CREDIT CARDS and
separates them in order to allow for separate waste disposal.
In all models KOBRA 245TS capable to shred optical media,
CDs,DVDs and Credit Cards should be inserted into the paper
feed opening.
10