HERKULES AHW 2500/1 Instructions D'origine page 11

3. Proper use
The equipment is designed for transporting goods
on pallets with an open base or with stringer
boards extending beyond the load wheels. The
equipment must be used on a fi rm, fl at surface.
It is prohibited to use the equipment to pick up or
transport people.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
4. Technical data
Overall height: ...................................... 1210 mm
Overall length: ...................................... 1500 mm
Fork length: .......................................... 1150 mm
Fork height min.: ....................................... 85 mm
Fork height max.: .................................... 195 mm
Fork width single: ................................... 156 mm
Fork width total: ...................................... 550 mm
Lift max.: ................................................ 110 mm
Load: ........................................................2500 kg
Weight approx.: ...........................................66 kg
Steering wheels Ø: ................................. 180 mm
Load-bearing rollers Ø: ............................. 80 mm
5. Assembly
Note: The hydraulic system is secured with a bolt
(M). Do not remove it until prompted in the fol-
lowing assembly description and keep it in a safe
place for future maintenance work.
1. (Fig. 1) Press down the control lever (2) as far
as it will go into the lowering position (see 6.
Functions).
2. (Fig. 2) Pass the control chain (F) through
and out of the recess at the bottom end of the
drawbar.
3. (Fig. 2) Insert the bolt (B) through the hole
in the drawbar mount (C) and the hole in the
drawbar. Make sure that the clamping sleeve
passage (E) coincides with the clamping
sleeve hole in the bolt (B).
4. (Fig. 3) Pass the control chain (F) through the
hole in the bolt (B) so that the hydraulics sys-
Anl_AHW_2500_1_SPK7.indb 11 Anl_AHW_2500_1_SPK7.indb 11
GB
tem works.
5. (Fig. 3) Press down the foot pedal (8).
6. (Fig. 4) Hook the setting screw (H) with the
pre-mounted hex nut (K) into the hydraulics
lever (L). If necessary, screw the upper set-
ting nut (N) a little further upwards in order to
make it easier to hook in place. Release the
foot pedal again. Screw the upper setting nut
(N) against the hydraulic lever (L).
7. (Fig. 5) Press the drawbar (3) down a little so
that the hydraulics lock bolt (M) is slackened
and can be removed.
8. (Fig. 6 and 7) Check whether the clamping
sleeve mount of the bolt (B) coincides with
the clamping sleeve passage (E) in the draw-
bar mount. Use a hammer and the hydraulics
lock bolt (M) to hit the sleeves (A) into the bolt
(B) on the left and right.
Note: The equipment can be optionally equipped
with a foot-activated parking brake. If required,
please contact your customer service team.
Operating the foot-activated parking brake:
Push the brake to the right as far as the stop – the
wheels will be blocked.
Push the brake to the left – the wheels will be
released again.
6. Functions
Important! Note the safety information (section 1.)
and Figure 9.
On the drawbar is a sticker showing the positions
of the handle switch (Fig. 8).
1 = Lower (lowering position)
2 = Travel (traveling position)
3 = Lift (lifting position)
The pallet lifting truck is allowed to be parked only
when the lifting forks are lowered.
The following functions are possible and were
already set in the factory.
6.1 Lifting the load (Fig. 1)
Press down the control lever (2) (lifting position).
Then pump the drawbar (3) up and down several
times. The load will be lifted.
- 11 -
20.05.15 15:56 20.05.15 15:56