Walter Meier JET JPT-260 Mode D'emploi page 5

Drawing-in/trapping hazard by power
feed mechanism.
Squeezing hazard by work piece
power-outfeed.
Sawdust and noise can be health
hazards.
Be sure to wear personal protection
gear such as safety goggles and ear
protection. Use a suitable dust
exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications
4.1 Technical data
JPT-260:
Planing
Jointing width
Table length
Height above floor
Fence size 1100 x 150mm
Fence tilt
Depth of cut
Thicknessing
Thicknessing width
Thicknessing height
Thicknessing table length
Min. length of work piece
Feed speed
Depth of cut
Number of knives
Cutter block diameter
No load speed n
o
Cuts per minute
Cutter knife length
Cutter knife width
Cutter knife thickness
Dust port diameter
Overall (LxWxH) 1120x700x1000
Net Weight
Mains 230V ~1/N/PE 50Hz
Output power 1,7 kW (2,3 HP) S1
Reference current
Extension cord (H07RN-F) 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 1,7 kW (2,3 HP) S1
Reference current
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection
JPT-310:
Planing
Jointing width
Table length
Height above floor
Fence size
Fence tilt
Depth of cut
Thicknessing
Thicknessing width
Thicknessing height
Thicknessing table length
Min. length of work piece
Feed speed
Depth of cut
Number of knives
Cutter block diameter
No load speed n
Cuts per minute
Cutter knife length
Cutter knife width
max 257 mm
Cutter knife thickness
1120mm
Dust port diameter
850mm
Overall (LxWxH) 1400x750x1000mm
0 - 45°
Net Weight
max.3 mm
Mains
Output power
max 256 mm
Reference current
3 - 225 mm
Extension cord (H07RN-F) 3x1,5mm²
540mm
Installation fuse protection
150mm
Mains
5,5 m/min
Output power
max. 4,5 mm
Reference current
3
Extension cord (H07RN-F) 4x1,5mm²
70 mm
Installation fuse protection
5500 rpm
16500
260 mm
JPT-410:
15 - 25mm
Planing
3mm
Jointing width
100mm
Table length
Height above floor
Fence size
170 kg
Fence tilt
Depth of cut
Thicknessing
10 A
Thicknessing width
Thicknessing height
16A
Thicknessing table length
Min. length of work piece
Feed speed
3,5 A
Depth of cut
Number of knives
16A
Cutter block diameter
No load speed n
Cuts per minute
Cutter knife length
Cutter knife width
Cutter knife thickness
Dust port diameter
max 307 mm
1400mm
850mm
1100 x 150mm
0 - 45°
max.3 mm
max 307 mm
3 - 225 mm
540mm
150mm
7 m/min
max. 4,5 mm
3
70 mm
5500 rpm
o
16500
310 mm
15 - 25mm
3mm
100mm
230 kg
230V ~1/N/PE 50Hz
2,2 kW (3 HP) S1
13 A
16A
400V ~3/PE 50Hz
2,2 kW (3 HP) S1
5 A
16A
max 407 mm
1660mm
850mm
1100 x 150mm
0 - 45°
max.3 mm
max 407 mm
3 - 225 mm
600mm
150mm
7 m/min
max. 4,5 mm
3
70 mm
5500 rpm
o
16500
410 mm
15 - 25mm
3mm
120mm
5
Overall (LxWxH) 1660x870x1000mm
Net Weight
Mains 230V ~1/N/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F) 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 3 kW (4 HP) S1
Reference current
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection
4.2 Noise emission
Determined according to EN 861
(Inspection tolerance 4 dB)
Work piece pine wood:
W=100mm, L=1000mm, moisture
8,5%
Planing:
Acoustic power level
(according to EN ISO 3746):
Idling LwA 89,8 dB(A)
Operating LwA 101,8 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA 78,9 dB(A)
Operating LpA 96,5 dB(A)
Thicknessing:
Acoustic power level
(according to EN ISO 3746):
Idling LwA 92,6 dB(A)
Operating LwA 103,5 dB(A)
Acoustic pressure level
(according to EN 11202):
Operating position 1:
Idling LpA 74,4 dB(A)
Operating LpA 91,8 dB(A)
Operating position 2:
Idling LpA 84,4 dB(A)
Operating LpA 95,7 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
Although there is a correlation
between emission and imission levels,
these do not constitute a basis for
determining the necessity of additional
safety measures.
Workplace conditions which could
influence the noise imission level
include the duration of resonance,
spatial particulars, other noise
sources etc. For example, the number
of machines and other work being
performed. The permissible workplace
levels can vary from country to
country.
315 kg
13 A
16A
6,5 A
16A