Programming The User Code; Operating Sound Features - Master Lock LFW082FTC Mode D'emploi

Slide out the battery drawer
2
A
on the side of the keypad.
Insert 4 AAA alkaline
B
batteries (not included)
Note: Do not use rechargeable
batteries or any other type of
non-alkaline battery. Do not mix
old and new batteries. Do not mix
alkaline and standard batteries.
Slide battery drawer back
C
into keypad.
Find your 5 digit factory code on
3
the
M100TEST back of this owner's manual.
SN100TEST01*
12345
WARNING: Test your code several times before putting
valuables inside.
Unlocking your safe
FOR DUAL KEY/COMBINATION
1
LOCKS ONLY, insert key into the
lock, turn to the 'unlocked'
position, then remove the key
This is a secondary locking
feature not an override key.
2 Enter the 5 digit factory code
A
found on the back of the
owner's manual.
Note: You may have to lift
the handle while entering
the combination.
A green light will indicate the
B
code is correct. You will have
4 seconds to turn the handle
to unlock your safe.
3 Rotate the handle downward to
open the door.
This may take a limited
amount of force if you have a
water-resistant safe.
NOTE: • Make sure the handle is rotated all the way up in the
horizontal position before unlocking the safe.
• If you exert too much force on the handle, the handle will
move without moving the bolts. If this happens, you will
hear a 'click.' DO NOT be alarmed. This feature is designed
to protect the bolts from being over powered by force. If this
occurs, simply exert force in the opposite direction (lifting up)
until the handles 'clicks' back into place and repeat steps 1-3
to open your safe.
• Delay mode will occur if three consecutive invalid entries have
been tried. Red LED will blink on and off to let you know the
safe is in delay mode. This will cause the system to shutdown
for two minutes. DO NOT remove the batteries to restart the
system it will only increase the length of time for the system
shutdown.
Locking your safe
Close the door and pull the
1
handle upward until the handle is
horizontal.
For water-resistant units,
additional pressure to the front,
left side of the door may need
to be applied prior to rotating
the handle.
FOR DUAL KEY/ELECTRONIC
2
LOCKS ONLY, insert key into the
lock, turn to the 'locked' position,
then remove the key.
NOTE: If your safe does not
appear to be working properly,
please check to make sure you
are using NEW alkaline batteries
before contacting Master Lock
Customer Service.
Programming information
Three code options:
Factory code:
The safe will ALWAYS unlock using
this 5 digit code (found on the back of
the owner's manual). This code cannot
be deleted.
User code:
A 5 digit programmable code of your
choosing that can be changed or
deleted or changed.
Secondary code:
A second 5 digit programmable code of
your choosing that can be changed or
deleted. Can only be programmed after
a user code has been activated.
NOTE: • The "C" key is a clear key. This can be used at anytime to
clear the system and return to standby mode – unless you are
in delay mode (3 consecutive invalid entries).
• The 5 digit factory code cannot be deleted. However, you may
add and delete additional codes.
This safe can store up to three codes at one time. One factory
code and two additional programmable codes.

Programming the user code

To ADD a user code:
1
Press the "P" key.
2
Enter the 5 digit factory code found on the back of your owner's
manual.
3
The light will flash green and then you will have five seconds to
enter your own personal 5 digit user code.
To DELETE a user code:
1
Press the "P" key.
2
Enter the 5 digit factory code.
3
Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
user code – please test the code to make sure it has been
deleted.
• Test with door open when programming.
Programming the secondary code
To ADD a secondary code:
1
Press the "P" key two times.
2
Enter the 5 digit user code previously programmed.
3
The light will flash green and then you will have five seconds to
enter your own personal 5 digit secondary code.
To DELETE a secondary code:
1
Press the "P" key two times.
2
Enter the 5 digit user code.
3
Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
secondary code – please test the code to make sure it has
been deleted.
How to operate the light
The safe you have purchased may include a light. This is a long-lasting
LED light. Not all safes include a light.
The batteries that operate the keypad
are the same batteries that operate the
light. If the light in your unit does not
turn on, please change your batteries.
The light will turn on every time you
enter your code and will remain on
for 30 seconds. The light duration has
three options – off, 30 seconds, and 60 seconds.
To turn the light off:
1
Press the "0" button.
2
Press the "P" button.
3
Press the "3" button.
To turn the light on for 30 seconds:
1
Press the "0" button.
2
Press the "P" button.
3
Press the "4" button.
To turn the light on for 60 seconds:
1
Press the "0" button.
2
Press the "P" button.
3
Press the "5" button.
NOTE: • If the light duration is 60 seconds, the battery life will be
reduced at a faster rate.

Operating sound features

For Programmable Electronic Lock Only
The tones of the key pad may be turned on and off depending on user
preference.
Turn sound off:
1
Press "O".
2
Press "P" key.
3
Press "2".
Turn sound on:
1
Press "O".
2
Press "P" key.
3
Press "1".
ENGLISH
3