General Information - Sharp BOY Manuel D'utilisation Et Entretien

1. SAFETy:
ATTENTION! When you use electrical machines,
you should always observe basic safety precau-
tions to reduce the risk of fire, electric shocks and
personal injuries.
- Do not leave the machine out in the rain.
- Do not use the machine in damp or wet places.
- Keep the work area well lit.
- Do not use the machine near flammable liquids or gas.
- Make sure the voltage and the frequency written on the
rating nameplate match those of the mains.
- Make sure the switch is not pressed down and blocked
before you plug the machine into the mains to prevent it
from starting up accidentally.
- Unplug the machine from the mains when it is not in use,
before you start any maintenance jobs and when you
replace any accessories (e.g. grinding wheel).
- Before you actually use the machine, make sure it is able
to work appropriately and efficiently: check the integrity of
the grinding wheel guard in particular.
- Check the alignment and adherence of moving parts, make
sure nothing is broken, check the overall assembly and any
other conditions that may affect operation.
- The grinding wheel safety guards and any other parts dam-
aged shall be repaired or replaced by a skilled technician,
unless specified otherwise in this manual.
- Have faulty switches replaced by a skilled technician.
- Keep anyone that is not involved in the job well away from
the work area, especially children. Do not let them touch
the machine or the extension lead.
- Wear safety goggles and gloves.
- Wear a face mask or dust mask if the process creates dust.
- Do not wear baggy clothing or jewellery, which could get
caught up in moving parts.
- Wear a protection cap to tie long hair back.
- Wear non-slip shoes when working outdoors.
- Always stand appropriately and balanced on both feet.
- Always keep your eyes on the job, without distraction. Use
your common sense and do not use the machine if you
are tired.
- Always make sure spanners and tools have been taken
off the machine before using it.
- Keep the work area clean and tidy. Untidy work areas and
benches could increase the risk of an accident
- Do not touch earthed surfaces with any part of your body.
- Always use the vise to firmly hold the chain to be sharp-
ened. Never sharpen the chain while holding it with your
hands.
- Do not force the machine to work at a higher speed than
that envisaged.
- Never stop the grinding wheel with your hands, even after
the motor has been switched off.
6
EN
- When using the machine outdoors, use extension leads
approved for such use and marked accordingly.
- Never pull on the power cable to unplug the machine from
the mains. Keep the cable away from heat, oil and sharp
edges.
- Do not use the machine if the switch does not switch on
or off.
- The use of accessories (e.g. grinding wheel) different from
those recommended by the manufacturer could cause
injuries.
- Do not tamper with the safety devices.
- Look after the machine with care.
- Follow the instructions when replacing accessories.
- Every now and again, visually check the machine cable
and have it repaired by a skilled technician if you should
notice any damages.
- Every now and again, visually check the extension leads
and replace them if damaged.
- Keep the operating handles dry, clean and free from oil
and grease.
- When the machine is not used, keep it in a dry and safe
place away from children's reach.
- This electrical machine complies with related safety provi-
sions. Repairs shall be carried out exclusively by a skilled
technician, using exclusively OEM spare parts, otherwise
whoever uses the machine could be in serious danger.

2. GENERAL INFORMATION

The manufacturer is not liable for damages in the following
cases:
- failed observance of the instructions given herein;
- use of the machine other than that described in the
"INTENDED USE" section;
- failed use in compliance with current standards on Health
& Safety at the workplace;
- Incorrect installation;
- lack of scheduled maintenance;
- modifications or jobs that are not authorized by the
manufacturer;
- use of non-original or inadequate spare parts;
- repairs that are not carried out by a skilled technician.
3. WARRANTy
The warranty validity is that acknowledged in the country
of sale. Claims under warranty will only be accepted
if they are backed-up by the copy of the purchase
document (bill or receipt).
The guarantee becomes void if:
a) the machine has been tampered with;
b) the machine has not been used according to this manual;
c) non-original parts, machines or grinding wheels have been
fitted on the machine or other parts that are not authorized
by the manufacturer;
d) the machine has been powered at a voltage or frequency
different from that written in the rating nameplate.
4. USE AND CARE OF THE OWNER'S MANUAL
The characteristics and the information given in this manual
are merely indicative. The manufacturer reserves the right to