Before Starting The Equipment - Bavaria BLK 65 Mode D'emploi D'origine

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Information
•
Remove all adhesive retention tapes before
putting the equipment into operation. There
are accessories in the water container or/
and under the fl ap.
•
Please note that the minimum distance bet-
ween the equipment and the wall to the side
and rear must be 40cm. The minimum dis-
tance to other objects at the front must be 1m.
•
The device must never be tilted, moved or
emptied while switched on or while connec-
ted to the power supply.
•
Only ever move the device when the water
tank is empty and the device has been dis-
connected from the power supply.
•
Use only clean, cold tap water or distilled
water.
•
Never add any scents or fragrances to the
water.
•
Ionizer: Ionization of the air can create a cli-
mate which can otherwise only be found at
the sea or in mountainous regions. It reduces
the concentration of microorganisms in the air
and helps with the oxygen enrichment of the
blood and with the development of resistance
to germs and allergies.
•
The negative ions which are generated may
cause a small electrostatic charge on the air
outlet fins. This is normal and is not dange-
rous.
•
Never use the device in rooms with excessive
concentrations of oxygen (e.g. in laboratory
rooms or in rooms in which oxygen-producing
devices are used).
•
The settings which have been made are
shown on the LED display. The applicable
LEDs shine.
5.2 Filling in water (Fig. 3/4)
•
Turn the lock (A) into the horizontal position
and pull out the water container (7) from the
back of the equipment.
•
Plug in the ice cube tray (11).
•
Fill up the water container (7). Make sure that
the water level lies between the „min" and
Anleitung_BLK_65_SPK7.indb 16 Anleitung_BLK_65_SPK7.indb 16
GB
„max" marks.
•
To improve the cooling effect you can place
normal ice cubes in the ice cube tray (11) and
frozen cooling elements (Fig. 2/Item 10) in the
water container (7).
•
Make sure that the foam filter (12) is inserted.
Push the water container (7) back into the
housing. Turn the lock (A) back into the verti-
cal position.
•
Replace the water once a week.
5.3 Installing the air fi lter (Fig. 5)
Push the air fi lter (4) into its guides from above.
6. Operation (Fig. 6)
Insert the power plug into a live socket outlet. The
„Power" LED will light up.
6.1 Switching the equipment on/off (Item 20)
Press the ON/OFF button to switch on the equip-
ment. Air will then be blown out at medium, uni-
form fan speed. Press the button again to switch
off the equipment.
6.2 Switching on the ionizer (Item 21)
Press the „ANION" button to switch on the ionizer.
The „ANION" LED will light up.
6.3 Switching on the vertical slat adjustment
(Item 22)
Press the „VANE" button for the vertical slats to
swing automatically back and forth. Press the but-
ton again to switch off this function. The horizontal
slats can be adjusted by hand with the levers (Fig.
7/Item B).
6.4 Switching on fan mode (Item 23)
The fan is set to „Normal" as standard. Press the
„MODE" button to change the setting in the fol-
lowing order: Normal – Natural – Sleep. The LEDs
will light up accordingly.
Normal: Uniform fan speed
Natural: Non-uniform fan speed
Sleep: The fan speed slows down in accordance
with a timed sequence until the fan stops.
HI/SLEEP = 1h high -> 1h medium -> 1h low ->
stop
MI/SLEEP = 1h medium -> 1h low -> stop
LO/SLEEP = 1h low -> stop
- 16 -
13.11.14 15:42 13.11.14 15:42