Important Safety Instructions - Lab.gruppen E Série Mode D'emploi

Introduction
The information contained in this Quick Start Guide is sufficient for proper installation of E Series amplifiers, and for configuration of
settings in typical applications. Please refer to the full Operation Manual for detailed information on maintenance, cooling requirements,
warranty, and configuration for complex installations .

Important safety instructions

1. Read these instructions.
2. Keep these instructions
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Do not connect the unit's output to any other voltage source,
such as battery, mains source, or power supply, regardless of
whether the unit is turned on or off.
16. Do not remove the top (or bottom) cover. Removal of the cover
will expose hazardous voltages. There are no user serviceable
parts inside and removal may void the warranty.
17. An experienced user shall always supervise this professional
audio equipment, especially if inexperienced adults or minors
are using the equipment.
Norge: Apparatet må tilkoples jordet stikkontakt
Sverige: Apparaten skall anslutas till jordat uttag
Suomi: Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan"
Standards
This equipment conforms to the EU
requirements of the EMC Directive 2004/108/
EC and Low Voltage Directive 206/958/EC
valid until April 19. 2016.
From April 20. 2016 the equipment complies
to EU directives for EMC 2014/30/EC and Low
Voltage Directive 2014/35/EC
Standards applied: EMC Emission
EN55103-1, E3
EMC Immunity EN55103-2, E3, with S/N
below 1% at normal operation level.
Electrical Safety EN60065, Class I
This equipment is tested and listed according
to the U.S. safety standard ANSI/ UL 60065
and Canadian safety standard CSA C22.2
NO. 60065. UL made the tests and they
are a Nationally Recognized Testing
Laboratory (NRTL).
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his
own expense.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This Class A digital apparatus complies with Canadian ICES-003.
Français: Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
2