Table des Matières
Publicité
18
BUGERA 6262 INFINIUM/6262-212 INFINIUM/6260 INFINIUM/6260-212 INFINIUM
BUGERA 6262 INFINIUM/6262-212 INFINIUM/6260 INF INIUM/6260-212 INFINIUM Controls
Step 2: Controls
Front Panel
(EN)
(1) POWER switch is used to turn the power of the
BUGERA amplifier on and off.
(2) STANDBY switch allows you to place the amp
in STANDBY mode. This way the amp is idle,
but the operational temperature of the valves is
maintained (POWER switch turned on).
Attention!
To avoid damage to your amp, never use
the BUGERA valve amplifier without a
loudspeaker connected!
(3) REVERB control determines the amount
of the built-in reverb effect. The 6262
INFINIUM (and 6262-212 INFINIUM) features
individual REVERB controls for the LEAD and
CLEAN channels. The supplied footswitch
lets you activate the REVERB effect
(see Chapter "Footswitch").
(4) PRESENCE control modifies the amp's damping
factor at high frequencies. This is used to fine-
tune the high-frequency range of the speaker
cabinet. The 6262 INFINIUM (or 6262-212
INFINIUM) features individual PRESENCE controls
for the LEAD and CLEAN channels.
(5) LEAD-VOLUME control lets you adjust the
volume level of the LEAD channel.
(6) CLEAN-VOLUME control that lets you adjust the
volume level of the CLEAN channel.
(7) TREBLE control adjusts the upper frequency
range. The 6262 INFINIUM (and 6262-212
INFINIUM) features separate TREBLE controls for
the LEAD and CLEAN channels.
(8) MID control adjusts the middle frequency range.
The 6262 INFINIUM (and 6262-212 INFINIUM)
features separate MID controls for the LEAD and
CLEAN channels.
(9) BASS control adjusts the lower frequency range.
The 6262 INFINIUM (and 6262-212 INFINIUM)
features separate BASS controls for the LEAD
and CLEAN channels.
(10) LEAD-GAIN control specifies the input level
of the LEAD channel. Turn the control to the
right to increase the preamplifier's distortion
and sustain.
(11) LEAD switch activates the LEAD channel
(switch glows red).
bugera-amps.com
(12) CRUNCH switch activates the gain boost on the
CLEAN channel (switch glows yellow). This way
the CLEAN channel can be used as a second
LEAD channel.
(13) CLEAN-GAIN control specifies the input level
of the CLEAN channel. Turn the control to the
right to increase the preamplifier's distortion
and sustain.
(14) CLEAN switch activates the CLEAN channel
(switch glows green).
(15) BRIGHT switch activates an extra boost in
the high-frequency range (+6 dB at 2 kHz)
which only affects the CLEAN channel.
(16) LOW GAIN input is used for instruments with an
extremely high output level that could distort
the HIGH GAIN input (only 6260 INFINIUM and
6260-212 INFINIUM).
(17) HIGH GAIN input (equals 6262 INFINIUM and
6262-212 INFINIUM INPUT socket) is 6 dB louder
than the LOW GAIN input and is used for most
electric guitars.
Rear Panel
Caution!
Hot! Risk of injury! During use, the valves get
very hot and high surface temperatures may be
reached at the rear of this unit. Avoid touching
the controls and connectors on the rear panel
during use.
(18) FX LOOP SEND output is used to connect a
shielded ¼" mono jack cable to the input of an
external effects unit.
(19) FX LOOP RETURN input is used to connect a
shielded ¼" mono jack cable to the output of an
external effects unit.
(20) PREAMP OUT SEND output takes the preamp
signal of the amp in order to feed the signal to a
second amplifier and loudspeaker combination,
for example.
(21) FOOTSW(itch) 5-pin connector is provided
to connect to the supplied BUGERA FSB104A
footswitch. Please be sure to connect the cables
before switching on the amplifier. Refer to
"Footswitch" for details.
(22) INFINIUM VALVE LIFE MONITORING section
shows correct biasing for each valve separately.
When an output valve requires replacement,
the valve's matching LED will light permanently.
19
Quick Start Guide
(23) IMPEDANCE switch lets you specify the
loudspeaker impedance. Always apply the value
that is identical to the impedance of the used
speaker cabinet.
(24) LOUDSPEAKER parallel outputs (¼" mono jacks)
are used to connect the speaker cabinet(s).
The minimum impedance is 4 Ohms.
Always use loudspeaker cables for connection
between the amplifier and the loudspeaker.
Never use other types of cable such as instrument
cable and microphone cable.
Attention!
To avoid damage to your amp, never use
the BUGERA valve amplifier without a
loudspeaker connected!
WARNING: ONLY REPLACE THE FUSE WHEN
THE MAINS CABLE HAS BEEN DISCONNECTED!
If the fuse is blown, it needs to be replaced
with a fuse of the same kind by all means.
Otherwise, the unit could seriously be damaged,
in which case the warranty is void.
(25) FUSE is found in the fuse holder.
(26) IEC connector is used to connect the mains cable
that has the appropriate voltage ratings for your
country (included).
(27) SERIAL NUMBER of the amplifier.
Footswitch
(28) DIN cable (5-pin) to connect Footswitch to
the FOOTSW connector on back panel of the
BUGERA amplifier.
(29) CLEAN switch activates the CLEAN/CRUNCH
channel. Its LED illuminates when the channel
is active.
(30) LEAD switch activates the LEAD channel. Its LED
illuminates when the channel is active.
(31) REVERB switch activates the REVERB effect.
Its LED illuminates when the effect is active.
(32) FX LOOP switch activates the FX LOOP function.
Its LED illuminates when the FX LOOP is active.
bugera-amps.com
Publicité
Table des Matières
