Unpacking The Appliance; Initial Operation - Clatronic DR 3280 Mode D'emploi

Unpacking the Appliance

1. Remove the appliance from its packaging.
2. Remove all packaging material such as plastic films, filler
material, cable ties and cardboard packaging.
3. Check the content for any missing parts.
4. In the event that the packaging content should be incom-
plete or if damages are noticeable, do not operate the
appliance. Return it to the dealer immediately.
NOTE:
There may be dust and production residue on the appli-
ance. We recommend cleaning the appliance as described
under "Cleaning".

Initial Operation

Filling up the Heating Boiler before Use!
Before the tank cap is opened it must be ensured that the ap-
pliance is not under any pressure. Please proceed as follows:
1. Remove the plug from the socket.
2. Turn the lock (22) on the steam pistol (20) to ON (Fig. B1).
3. Press the steam switch (21) on the steam pistol (Fig. B2).
Point the steam nozzle at a surface which is allowed to
become wet.
NOTE:
After prolonged periods of non-use it is normal for a small
quantity of condensation to come out of the steam pistol
at first.
WARNING:
• If the appliance is still warm after an interruption to
its use there is a danger of injury!
• Please open the safety lock (6) only when no more
steam comes out of the nozzle.
4. Turn the lock in an anticlockwise direction.
5. Shake any residual water out of the kettle (7). Fill fresh-
water from the measuring beaker (15) into the kettle. Take
care of water splashes that might come out of the boiler.
In order to avoid water spray, please use the funnel sup-
plied (Fig. C). The water should be filled in slowly.
NOTE:
• The maximum filling capacity is 1.5 litres. Use the
measuring cup provided.
• Recommendation: Use distilled water to prevent
calcification.
CAUTION:
Do not use battery water, water from tumble dryers or water
with additives such as cleaning agents, alcohol, fabric
softener or other chemicals. They could cause hazards or
damage to the appliance.
6. Re-tighten the safety lock (6) in a clockwise direction.
DR3280_IM_new2
Attachment of the Individual Accessories
It is possible to attach the individual nozzles directly to the
steam pistol (20) of the hose (1):
• Plug the adapter (14) onto the steam gun until it clicks
into place.
• To detach the adapter again, press the button on the
steam gun.
• Keep the button pressed and pull out the adapter.
Or extend the nozzle attachments with one or two extension
tubes (8):
• Please insert the sections of the 2-part extension tube
one inside the other until it locks into place (Fig. E). Then
attach it to the steam pistol (20).
• Attach the floor brush (18) to the extension tubes: press
the jointed adapter (17) on to the floor brush and turn it
tightly through 180 °.
• If you would like to use the non-woven cloth, attach it to
the floor brush with the help of the clips (Fig. F).
• In order to release the extension tube, please press the
button on the steam pistol.
NOTE:
Various attachments can only be used in conjunction
with the adapter (14). Check that everything is properly
connected!
Nozzle Adapter Use
Floor brush Jointed • for large floor surfaces
(18) adapter
(17) • with non-woven cloth: for
Round with • for joints, fittings, grill grid
brushes adapter
(11) (14) • for difficult-to-access areas
High-pres- with • for concentrated, high
sure nozzle adapter
(12) (14)
Window with • for windows or shower
wiper (19) adapter
(14)
WARNING: Danger of injury!
Never attach or remove the accessories if the steam switch
(21) is pressed in! Wait until the appliance has cooled down.
Electrical Connection
Before inserting the plug into the socket. Make sure that the
mains voltage to be used matches that of the appliance. You
can find this information on the nameplate.
(Fig. H)
sensitive surfaces (Fig. I)
etc. or
(Fig. G and J)
steam pressure (Fig. K)
partitions
37
10.07.18