Accoppiamento Elettrico; Electrical Connections - Mecc Alte spa ECSO 28 Manuel D'instruction Et De Maintenance

Table des Matières

Publicité

ACCOPPIAMENTO
ELETTRICO
L'accoppiamento elettrico e' a cura dell'utiliz-
zatore finale ed e' eseguito secondo la sua
sola discrezione.
Per l'ingresso nella scatola morsetti si racco-
manda di utilizzare passacavi e serracavi in
accordo con le specifiche del paese di
esportazione.
COLLEGAMENTO AVVOLGIMENTI
(tav. 2 pag. 41) .
Sono previsti entrambi i collegamenti, stella
con neutro ( Y ) e triangolo ( ∆ ) in tutti gli
alternatori.
Per passare da un collegamento Y a ∆ (es.
da 400V a 230V) e' sufficiente spostare i
ponti sulla morsettiera principale (vedere
schema tav. 2 pag. 41)
Nessun intervento e' richiesto nel sistema di
regolazione.
I generatori sono costruiti di serie con 12 cavi
di uscita per consentire di ottenere tensioni
diverse (es.115 / 200 / 230 / 400V ).
I generatori, vanno sempre collegati a terra
con un conduttore di adeguata sezione
utilizzando uno dei due (interno/esterno)
appositi morsetti.
Dopo aver eseguito il collegamento rimon-
tare il coperchio scatola morsetti.
VERSATILITA' DI FUNZIONAMENTO
50 - 60 Hz
La serie ECSN - ECSO puo' funzionare
indifferentemente sia a 50 che a 60Hz.
Nel generatore ECSN - ECSO con
regolazione solo compound, la tensione
generata varia con il variare della velocita'.
Puo' essere necessario che si debba
riaggiustare la tensione nel passaggio da
una frequenza all'altra: a tale proposito
vedere
paragrafo
"Regolazione
tensione".
Nel generatore ECSN - ECSO con AVIR si
devono cortocircuitare i previsti terminali per il
funzionamento a 60Hz, come illustrato alla
tav. 4 pag. 42.
La regolazione della tensione si ottiene
agendo sul potenziometro "Tensione" come
descritto nel paragrafo "Regolazione della
tensione".
Passando da 50Hz a 60Hz, la potenza puo'
aumentare del 20% (corrente invariata), se la
tensione aumenta del 20%; se la tensione
rimane invariata, la potenza puo' aumentare
del 5% per effetto della migliore ventilazione.
Per generatori costruiti appositamente per
una frequenza di 60Hz nel passaggio a
50Hz, la tensione e la potenza devono
necessariamente diminuire del 20% rispetto
a quelle riferite a 60Hz.
REGOLAZIONE DELLA TENSIONE
1) ECSN - ECSO CON REGOLAZIONE
SOLO COMPOUND
Regolazione della tensione a vuoto.
Per regolare la tensione a vuoto si dovrà
agire sull'intraferro del trasformatore (tav. 3
pag. 41) nel seguente modo :
della
22
ELECTRICAL
CONNECTIONS
All electrical output connections are the
responsibility of, and are at the discretion of,
the end user.
When making terminal box connections, all
cable and terminal lugs should meet the
relevant standards of the country of final
destination.
WINDINGS CONNECTION
(table 2 pag. 41) .
All alternators feature both star with neutral
( Y ) and delta ( ∆ ) connections.
To reconnect from a star to delta connection
(for ex. from 400V to 230V), modify the linking
arrangements on the output terminal board
(see diagram on table 2 page 41).
It is not necessary to adjust the voltage
regulator.
Standard alternators are equipped with 12
cables to offer different voltages (ex. 115 / 200
/ 230 / 400V).
The alterrnator must always be earthed by
sufficiently rated cable, using one of the inside
or outside terminals. After completing output
connections, ensure that the terminal box
cover is securely in place.
WORKING VERSATILITY 50-60 Hz
The ECSN - ECSO series can work at 50
as well as at 60 Hz. The ECSN - ECSO
generator with the only compound
regulator varies the output voltage by the
variation of the speed. It could be
necessary to regulate the voltage by
speed change. To do this, refer to the
paragraph "VOLTAGE REGULATION".
In the ECSN - ECSO generator with
AVIR the terminals foreseen for the 60
Hz must be shorted, as described in tab.
4 page 42.
The voltage regulation can be operated
through
the
potentiometer
"Tensione" as described in "Voltage
regulation" paragraph.
When changing from 50 to 60 Hz the
power can increase by 20% (with no
current change), if the voltage increase
by 20%; if the voltage does not change,
the power may increase by 5% due to
improved ventilation. For machines
wound for 60 Hz, changing to 50 Hz, the
voltage and power values have to
decrease by 20% of 60 Hz values.
VOLTAGE REGULATION
1) ECSN - ECSO WITH ONLY
COMPOUND REGULATION
No-load voltage regulation
To regulate the no-load voltage, act on
the air gap of the transformator (table 3
page 41) in the following way:
marked

Publicité

Table des Matières
loading

Table des Matières