Table des Matières
Publicité
Liens rapides
Owner's Manual / Mode d'emploi
Pat. # 8,491,685
Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art dust collection systems and material
handling ductwork to woodworking shops. OAS designs and manufactures industrial grade dust collection systems that
create a practical, safe and healthy work place environment.
Oneida Air Systems, Inc. a été fondée en 1993 pour mettre le coût, les systèmes état -of-the-art de dépoussiérage et de
manutention conduits efficace pour les ateliers de menuiserie. OAS conçoit et fabrique des systèmes de classe industri-
elle de la poussière de collecte qui créent un environnement pratique, sûr et sain lieu de travail.
Smart Hi-Vacuum
Appearance may vary slightly /
L'apparence peut varier légèrement
ZBM000105
5hp
Publicité
Table des Matières
Manuels Connexes pour Oneida Air Systems Smart Hi-Vacuum 5hp
Sommaire des Matières pour Oneida Air Systems Smart Hi-Vacuum 5hp
- Page 1 Oneida Air Systems, Inc. a été fondée en 1993 pour mettre le coût, les systèmes état -of-the-art de dépoussiérage et de manutention conduits efficace pour les ateliers de menuiserie. OAS conçoit et fabrique des systèmes de classe industri-...
- Page 2 System Start-Up Information Read the installation and maintenance instructions as well as the recommended safety practices in this manual. / Lisez les instructions d’installation et d’entretien ainsi que les pratiques de sécurité recommandées dans ce manuel. WARNING / AVERTISSEMENT Do not operate Fan / Blower unless Fan Housing is attached to DANGER Cyclone body and Dust Drum is in place.
-
Page 3: System Contents
System Contents Smart Hi-Vac Systems Parts List *Not to Size SCX002109 - Cyclone Cone - 1 SXI002108 - Cyclone Barrel - 1 BHX020005B - Fan Housing - 1 BHX001803 - Blower Cowling - 1 BXI050318 - Motor 5hp 3ph Smart- 1 FPZ000018 - Dust Bin - 2 FCS183900 - Filter 18”x 39”... - Page 4 General Specifications & Fan Performance Curves XXS050333 System 1789 Max. CFM Performance Outlet can be rotated independent of the inlet Height w/ 55 Gallon Drum: 107” Footprint w/ Ext. Cartridge: 40” x 48” System Inlet Diameter: Welded 7” w/ Neutral Vane Dimensions Powder Coated Paint Finish Over Heavy Gauge Steel Seam-Welded Cyclone...
-
Page 5: Stand Assembly
Stand Assembly (32) 5/16 Bolts (32) 5/16 Nuts (64) 5/16 Flat Washers 21 7/8” 21 7/8” 21 7/8” 21 7/8”... -
Page 6: Dimensions
Dimensions For Minimum Mounting Heights w/ 36” Filter & 55 Gal. Drum *Dimensions subject to slight variation in manufacturing. 107” 7” Dia. 26” 79” 28” 68” 54” Dimensions shown with 5” flex hose between drum and cone col- lar. / Dimensions indiquées avec 5 ‘... -
Page 7: Stand Assembly / Tenez Assemblée
Assembly Instructions / Instructions de montage Do NOT use hook on motor to lift unit. / NE PAS utiliser le With all assemblies, make sure rectangular air outlet is oriented on Fan/Blower housing as you crochet sur le mo- are looking down as in Fig. 1A or facing it as shown in diagrams. This is very important. / Avec teur pour soulever toutes les assemblées, assurez-vous que la sortie d’air rectangulaire est orientée sur le loge- l’unité. - Page 8 1. Attach gasket (RGZ025050) to the top of cyclone cone (SCX002109). Make sure you apply it inside the bolt holes around the cone top and it is important that you do not leave any gaps where the ends of the gasket meet. / Fixez le joint (RGZ025050) au sommet du cyclone cône (SCX002109).
- Page 9 7. Next attach Plenum Plate (FPX020018) to the pre-drilled holes in the stand legs, making sure that they are on the correct side for your collection purposes. / Fixez ensuite Plenum Plate (FPX020018) dans les trous pré-percés dans les jambes du support, en s’assurant qu’ils sont sur le bon côté...
-
Page 10: Flex Hose Connection Cone To Drum / Tuyau Flex Connexion Cone Drum
If you are having trouble getting your drum Drum Grounding Wire out to empty it, you can cut down the flex / Tambour Fil de terre hose to give yourself more room. Just make sure that the drum lid tightly seals to the drum To attach the Drum and that there are no leaks in the flex hose Grounding Wire, start a... - Page 11 Infrared Drum Level Sensor Assembly Strobe 2” - 3” Light Away from The placement of the Infrared Sensor is very important. The Sensor should Inlet not be more than 2 or 3 inches away from the inlet to the container. If it Infrared Sensor is farther away, it may not alert you to the overfilled dust level until it is too late.
-
Page 12: Filter Maintenance
Filter Maintenance External Filter Cartridge Cleaning Intervals / Intervalles Filtre externe cartouche de nettoyage When unit is turned off, use compressed air to blow dust off from exterior of filter. Hold nozzle at least 6” away from filter pleats*. Do not remove bottom dust pan before or during the blow-off process! Let dust settle into dust pan. -
Page 13: Fan Motor Maintenance / Moteur De Ventilateur Entretien
Fan Motor Maintenance / Moteur de ventilateur Entretien Per Baldor specifications, their 2 pole motors (3,600 rpm) are to be relubricated every 5,500 hours. / Par spécifica- tions Baldor, leurs deux moteurs de pôles (3600 rpm) doivent être graissés toutes les 5500 heures. Table 1 - Service Conditions / Conditions de service Ambient Temperature Type of Bearing / Type... - Page 14 Troubleshooting / Dépannage Note: If you continue to experience difficulty with your collector, call Oneida Air System's customer service at 866- 387-8822. / Si vous continuez à rencontrer des problèmes avec votre collecteur, appelez le service à la clientèle de Oneida Air System au 866-387-8822.
- Page 15 Filter Clogging / Colmatage du Filtre Caused By / Causée Par: Large chips clogging th filter -Check for a leak in the dust bin, flex coupling or lid. Check for split or torn flex coupling. (See also: Motor Overheating sec- tion) -Make sure dust bin has not over filled.
-
Page 16: Fire Hazards / Risques D'incendie
Fire Hazards / Risques D’incendie Read before installing and operating / Lire avant d’installer et d’exploitation. Wood shaping and cutting processes generate wood chips, shavings and dust. These materials are considered combus- tible. Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly). - Page 17 The customer assumes the responsibility for contacting their insurance underwriter with regard to specific application requirements of explosion venting or if additional fire protection and safety equipment may be required. / Le client assume la responsabilité de communiquer avec leur souscripteur d’assurance à l’égard des exigences spécifiques à l’application d’explosion ventilation ou si la protection incendie et équipements supplémentaires de sécurité...
- Page 18 - Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.) / Électriquement à la terre tout l’équipement et les conduits. Étincelles statiques peuvent enflammer la poussière de bois. (Évitez d’utiliser des tuyaux de vidange PVC.) - Don't allow accumulation of layers of fine dust on horizontal surfaces (especially overhead lights, electrical boxes and fuse panels which can ignite dust.) / Ne pas permettre l’accumulation de couches de poussière fine sur les surfaces horizontales (feux surtout les frais généraux, les boîtes électriques et des panneaux de fusibles qui peuvent enflammer la poussière.)
-
Page 19: How To Order
In no event shall Oneida Air Systems’ liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Oneida Air Systems shall be tried in the State of New York, County of Onondaga. / Bons Oneida Air Systems ™ les produits fabriqués par Oneida Air Systems, pour une période de 1 an ou plus selon le produit , à... -
Page 20: Returned Goods Policy / Politique De Retour De Marchandises
Products will be shipped to Buyer’s single destination. Title and risk of loss shall pass to the Buyer upon delivery to such destination. Buyer pays transportation expenses. Dates of shipment are advisory and Oneida Air Systems will make reasonable efforts to ship on or before the date states for shipment, however, Oneida Air Systems shall not incur any liability for failure to ship on that date.