Thetford SANICON TURBO 700 Mode D'emploi page 4

Operation, cont'd.
Empty Gray Water Tank(s)
Refer to the Fig. 1.
1. ENSURE universal nozzle (
station! Refer to "Attach to Dump Station" procedure.
TIP For Cleaner Storage: Emptying black water tank fi rst,
NOTICE
allows gray water to cleanse the system.
2. Open gray water tank gate valve (
3. Turn pump on.
4. Do not leave unit unattended.
TIP: The hose expands as fl uid moves to dump station
NOTICE
and contracts when tank is empty.
5. Turn pump off.
6. Close gray water tank gate valve
7. Repeat Steps 2-6 for secondary gray tanks.
Gray water bypass is possible if the discharge plumbing
NOTICE
does not fl ow upward.
Prepare Hose For Storage
Refer to the Fig. 1.
1. Ensure pump is off.
2. Empty hose ( ) by holding at a sloped angle to direct excess
F
water into the dump station.
TIP For Faster Draining: Leave gray gate valve
NOTICE
open allowing hose to vent and expediting the process.
3. Disconnect nozzle ( G ) from dump station.
4. Install cap(s) ( ).
H, I
5. Return hose to coach hose compartment (
nected to coach.
Helpful Hints
■ Empty the black water fi rst. Use gray water to rinse the
hose after emptying the black water.
■ Additional hoses can be purchased from Thetford and used
to extend the length of the evacuation hose. Connect the
hoses using 1.5 in. (3.8 cm) barbed coupling with clamp.
■ If you wish to extend the discharge hose, connect a 3/4
in (1.9 cm) inner diameter garden hose to the end of the
nozzle. Do not extend the hose beyond 150 ft. (45 m).
A longer discharge hose reduces fl ow rate.
NOTICE
■ Make sure the discharge hose is completely empty before
storing.
Gray water bypass is possible if the discharge plumbing
NOTICE
does not fl ow upward.
97515 Rev. E (06/10/2017)
G ) is securely attached to dump
M ).
(M) .
J ); leave hose con-
Obstruction Removal
NOTICE
1. Ensure all contents have been drained from system. If manual
over-ride ( K
open gate valve (
NOTICE
2. Locate impeller access cap (E); remove screws (6x).
3. Remove obstruction from impeller housing (not shown -
located above (
AVISO AVIS
! NOTICE CAUTION
4. Replace the O-Ring, Access Cap and Screws. Service Kit
comes with all new parts needed to reassemble.
NOTICE AVISO CAUTION AVIS
!
5. Ensure manual over-ride bypass gate valve (
reattach bayonet cap.
6. Operate system using gray water; check for leaks.
Manual Over-ride (Optional)
NOTICE
(M)
1. Locate manual over-ride connection (
2. Connect 3" sewer hose (not supplied): one end to (
end to dump station.
3. Open manual over-ride gate valve
4. Open black water gate valve; allow contents to drain.
5. Close black water gate valve.
6. Open gray water gate valve; allow contents to drain.
7. Close gray water gate valve.
8. Close manual over-ride gate valve.
9. Disconnect and clean sewer hose.
10. Install Manual Over-ride Bayonet Cap (
Winterizing
1. Ensure all tanks are empty.
2. Pour RV antifreeze into the empty black water tank (
3. Turn on pump.
NOTICE
4. Run pump until the antifreeze begins to discharge from
universal nozzle (
5. Turn pump switch to the Off position.
6. Empty hose (
excess water; return hose to storage position.
4
Dismantling the system can potentially cause the need
for new O-ring. Be sure to have a #238 Buna N O-Ring
(1x) on hand before following the steps below. Service
kits are available for purchase directly from Customer
Service.
) has been installed, remove bayonet cap, and
M ) to drain system contents.
Be sure to have container available for capturing system
fl uid!
)
E .
Do NOT remove pump lower housing. Obstruction
MUST be removed through impeller inlet.
Install screws in star pattern. Do NOT exceed 20 in. lb.
torque.
Optional installation. May not be installed on
your unit.
K ); remove bayonet cap.
.
K
Be sure to have container available for capturing system
fl uid!
).
G
F ) by holding at a sloped angle to remove
SANICON
M ) is closed;
), other
K
).
O ).
®
Turbo - Model 700