Office Star Products Space 2300 Instructions De Montage

11R
4
8,10
7
3
1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et s'assurer que les quantités des
pièces reçues sont correctes.
ÉTAPE 1
Insérer les roulettes (2) dans la base (1). S'assurer que toutes les roulettes sont insérées correctement.
ÉTAPE 2
Mettre la base en bois (1) debout de manière que les roulettes (2) soient sur le plancher. Insérer le vérin pneumatique (3) dans la base (1).
ÉTAPE 3
Attacher la plaque du siège (4) au coussin du siège (5) avec la flèche orientée vers l'avant du fauteuil en utilisant quatre vis
RESSERRER COMPLÈTEMENT LES QUATRE VIS.
ÉTAPE 4
Aligner les trous dans les bras (11L et 11R) sur les trous dans le coussin du siège (5). À l'aide de trois vis 1
(10), attacher chaque bras. RESSERRER COMPLÈTEMENT TOUTES LES VIS.
ÉTAPE 5
Attacher le support du dossier (12) à la plaque du siège (4) à l'aide de trois vis
NOTE IMPORTANTE: S'ASSURER D'AVOIR ASSEMBLÉ LE SUPPORT DU DOSSIER (12) DANS LA PLAQUE DU SIÈGE (5) ATTACHÉE AU COUSSIN DU
SIÈGE DANS L'ÉTAPE 4. (VOIR LE DESSIN DÉTAILLÉ A)
ÉTAPE 6
Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR RESSERRÉ COMPLÈTEMENT TOUTES
LES VIS.
2300/2400 FAUTEUIL PRÉSIDENT
INSTRUCTIONS DE MONTAGE
DESSIN DÉTAILLÉ A:
6
Installer le support du dossier dans
11L la plaque du siège
12
8,10
5
Pièce
7
1. Base . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . 1
4. Plaque du siège . . . . . . . . . . . . 1
5. Coussin du siège . . . . . . . . . . . 1
7
6. Coussin du dossier . . . . . . . . . 1
7
7. Vis / po . . . . . . . . . . . . . . . . . 4
8
8. Vis 1 3
/ po . . . . . . . . . . . . . . . . 6
8
5
9. Vis / po . . . . . . . . . . . . . . . . . 3
8
10. Rondelles plates . . . . . . . . . . 6
11. Bras gauche (11L) et droit
(11R) . . . . . . . . . . . . . . . . . . . 2
12. Support du dossier préinstallé .1
2 13. Clé Allen (non montré) . . . . . . 1
3
/ po (8) et de trois rondelles plates
8
5
/ po (9). RESSERRER COMPLÈTEMENT LES VIS.
8
9
3
Qté
1
WARRANTY
SPACE ® chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons
weighing 250 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism,
rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may
result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this
product. When usage is more than 40 hours per week, a five year warranty on all parts applies. Fabric is warranted for one year.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7
/ po (7).
8
All SPACE ® chairs are built to meet or exceed ANSI BIFMA standards.
To make a warranty claim, contact Parts Department via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a .m . - 5:00 p .m . Pacific Time . Provide model number and description of the
problem and obtain confirmation number . At it's option Office Star Products will:
(a) Supply compatible components of current manufacture .
(b) Repair the customer's component .
It is the customer's responsibility to prepay freight on any components returned to the factory . Return freight on components
covered by warranty will be paid by Office Star Products .
© Office Star Products June 2006
2300/2400 MANAGER CHAIR
OPERATING INSTRUCTIONS
FEATURE
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and pull lever (1)
up . To lower seat height sit on chair and pull lever (1) up .
• SYNCHRO TILT
To lock return chair to the upright position and push lever
(1) in . To unlock pull lever (1) out .
• TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change the
tension of the tilting feature . Turn knob (2) clockwise to
increase tension and counter-clockwise to decrease or
ease the tension .
NOTE: Be careful not to loosen back tilt adjustment knob
completely .
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to move up or
down freely. Release the button (3) once the desired height is reached.
WARNING
1 . Use this product only one person at a time .
2
2 . Do not use this chair unless all bolts screws and knobs are
securely tightened .
3 . Check that all bolts screws and knobs are tight every three
months or as needed .
4 . Do not overturn back tilt knob when decreasing tension .
5 . Dispose of packing material properly . Do not use plastic
cover as head covering . It may cause suffocation .
6 . Do not use chair as a stepladder .
7 . Use this chair for its intended purpose only .
8 . Use mild detergent only for cleaning .