Chapin 2014 Mode D'emploi

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pres-
surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or
leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-
tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or
body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution
from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify this sprayer. Replace parts only with manufacturer's original parts. Never spray flammable,
caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals.
Always read and follow chemical manufacturer's instructions before use with this sprayer as some chemi-
cals may be hazardous when used with this sprayer.
WARNING: Handling the brass parts of this product will expose you
to lead, a chemical known to the State of California to cause birth
defects and other reproductive harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse
suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-2001 3-6006 6-2000
Hose Fan Nozzle Shut-off Handle
Manguera Boquilla Mango de cierre
Tuyau Buse Poignée du robinet
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
To prevent hose from blowing off, hose must cover both barbs and touch
flange (fig. 1B) before hose nut is tightened (fig. 1C).
1. Hose to Tank
1A
Sk-1154-1
Do: Place end of hose
under hot tap water for 1
minute. This will soften
the hose and help insure
the hose is pushed all the
way down to the flange.
2. Nozzle
2A
Nozzle
Attach nozzle to shut-off handle or extension wand.
3. Filter
The filter helps prevent clogging while spraying. It is located on
the end of the outlet tube inside your sprayer tank. To clean filter,
remove the discharge assembly from the tank (Fig. 3A). Make
sure the filter is positioned at the bottom of the tank as pictured.
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior
of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
6-7749
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
Extension wand
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
Vara de extensión
Rallonge 4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any
of these conditions are found, replace affected part with original manufacturer's part before using.
6-1925
2-1093-5 (A) R0711
WARNING
1B 1C
Flange
Do: Push hose until it Do: Slide nut down
covers both barbs and over threads. Turn nut
touches the flange. clockwise as tight as
possible.
Wand
Nozzle
Shut-off
Shut-off
Handle
Handle
3A
Filter
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten
securely.
6. Pressurizing and Spraying
6A 6B 6C
Do: Turn handle clock- Do: Pump until you Do: Push handle, down,
wise to tighten. Push feel resistance. turn 1/4
handle down, turn 1/4 turn clockwise to lock.
turn counterclockwise to Begin spraying. Re-pump
release. sprayer as required to
maintain spray force.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are
thoroughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
8. Troubleshooting
- Tank pressurizes but does not spray.
WARNING: Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 8A- 8D)
8A Handle 8B 8C
Plunger
Diaphragm
Body
Pull handle Insert notches Remove plunger and dia-
straight up. from underside of phragm.
handle into plunger Clean plunger, diaphragm
grooves and turn and body. Flip diaphragm
counterclockwise. and replace.
Clean Nozzle Assembly (Fig. 8E) -Remove nozzle cap. Clean and re-assemble.
8E
Nozzle Cap
6D
Do: Turn end of
nozzle to adjust
spray pattern.
8D
Plunger flush
with body
Tighten plunger clockwise
until flush to top of shut-off
body. Do not over-tighten
or unit may not spray. Slide
forks under plunger, push
handle down until it snaps
into place.