tiSsi A252025 Instructions De Montage page 3

GB
Important safety instructions
Important – Read carefully before use – Keep in
a safe place for later consultation!
– Assemble the cot carefully and regularly check that all
screw connections are tight so as to rule out injuries
from trapped laces, chains, etc.!
– This product may only be used for its intended
purpose
as a cot.
– WARNING – Do not use the cot if parts are missing or
broken!
– Only those spare parts supplied by the manufacturer
may be used.
– WARNING – Never place the cot near a naked flame
or other strong source of heat such as an electric
radiant
heater, gas-fired stove etc
– Please note that lowest position of the bed base is the
safest. As soon as your child is old enough to sit, kneel
or pull him/herself up you must use this lowest position
of the bed base!
– WARNING – Never leave objects in the bed that your
child could use to climb up the sides or which constitute
a risk of suffocation or strangulation!
– The cot is designed for mattresses of the size 90X40
cm. The mattress may not be thicker than 0 mm; this
ensures that the surmountable side height of 500 mm in
the highest position and 200 mm in the lowest position
is not fallen short of.
– WARNING – Never use more than one mattress in the
cot.
– Only clean the piece of furniture with mild, common
detergent
and a moist, soft cloth. Remove any detergent residues
with lukewarm water. Leave the piece of furni-ture
to dry thoroughly before further use.
– If you leave your child unattended in the cot always
make sure that the removable slats are inserted
correctly.
– Always remove all removable slats if you want your
child to have free access to the cot.
– As soon as your child is able to climb out of the cot
you
should dismantle the sides so as to avoid any falls.
– The product is 00 recyclable.
– Subject to design modifications
Assembly instructions:
– Caution: any marks on the screw heads have been
caused
by a trial assembly in the works. This is your guarantee
for top quality.
– Do not use an electric (cordless) screwdriver for
assembly work!
– Only tighten all screws fully after complete assembly.
In
other words, only tighten screws loosely at first so as to
avoid any stress.
– Please note that there is always a danger of injury
when
working with tools or doing manual work. Therefore
please be careful when assembling this machine.
– Ensure that your working area is free of possible
sources
of danger, for example don't leave any tools lying
around. Always dispose packaging material in such a
way that it may not cause any danger. There is always
a risk of suffocation if children play with plastic bags!
– The equipment must be assembled with due care by
an
adult person. If in doubt call upon the help of a second
person, if possible technically talented.
– The fastening material required for each assembly
step
is shown in the diagram inset. Use the fastening mate-
rial
exactly as instructed.
– For technical reasons, we reserve the right to carry
out
preliminary assembly work (e.g. addition of tubing
plugs).
List of spare parts
When ordering spare parts, always state the full article
number, spare-partnumber, the quantity required and
the
Goods may only be returned after prior arrangement
and
in (internal) packaging, which is safe for transportation,
in
the original box if possible.
It is important to provide a detailed defect description /
damage
report!
Important: spare part prices do not include fastening
material;
if fastening material (bolts, nuts, washers etc.) is
required,
this should be clearly stated on the order by adding
the words „with fastening material".
Cleaning and maintenance
1. Only clean the product with a mild, standard detergent – never
a corrosive or environmentally unfriendly one – and a damp, soft
cloth.
2. It is possible that the colouring of the product can change over
time due to the effects of light. This does not constitute a defect.
3. When making spare parts orders, always state the item number
and the serial number of the product. Both can be found on the
silver-coloured label on the product.
Service
3