Remaining Hazards; Machine Specifications; Technical Data - Jet JBG-150 Mode D'emploi

Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit.
Use safety goggles at all times.
Use ear protection at all times.
Wear a face and dust mask when
working in a dusty environment.
Do NOT stop the abrasive wheel by
forcing the machine or by using
sideways pressure.
The material to be cut must be held
firmly so it can not move during
the cutting operation.
Never cut pieces that are too small.
Support long work pieces with helping
roller stands.
Never place your hand near the
cutting area while machine is in
operation.
Do not perform any operation
freehand; always have the
workpiece supported by the tool
rest.
Allow the abrasive wheel to come to a
complete standstill before using the
unit again or making adjustments.
Do not touch the machined
workpiece until it cools or you may
be burned!
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be bolted
on a firm workbench or stand.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Do not allow anyone to stand behind
the unit or close to the workpiece
where debris can be thrown.
Allow the abrasive wheel to reach full
speed before cutting.
Flying sparks will occur when cutting.
They can cause injury and ignite
flammable materials.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Make sure the tool operates properly.
Periodically check screws and bolts
for tightness.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine
adjustments or
maintenance with the
machine unplugged from
the power source.
Use only abrasive wheels rated at
3000 RPM or higher.
Remove defective abrasive wheels
immediately.
4

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving abrasive wheels in the
work area can cause injury.
Broken abrasive wheels can cause
injuries.
Thrown cutting chips, dust and noise
can be health hazards.
Be sure to wear personal protection
gear such as safety goggles, dust
mask and ear protection.
Some dust and gases created by
power cutting can be heath hazards.
To reduce your risk of exposure, work
in a well ventilated area.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.
Avoid body contact with earthed or
grounded surfaces (e.g. pipes,
radiators, ranges and refrigerators).

4. Machine specifications

4.1 Technical data

JBG-150:
Abrasive wheel
Shaft diameter Ø12,7mm (1/2")
No load speed
Wheel grits
Overall L x W x H 430 x 200 x 265mm
Weight
Mains 230V ~1L/N/PE 50Hz
Motor power
Reference current
Machine lamp
Extension cord (H07RN-F)
Installation fuse protection
Isolation class
JBG-200:
Abrasive wheel
Shaft diameter Ø15,9mm (5/8")
No load speed
Wheel grits
Overall L x W x H 440 x 230 x 290mm
Weight
Mains 230V ~1L/N/PE 50Hz
Motor power
Reference current
Machine lamp
Extension cord (H07RN-F)
Installation fuse protection
Isolation class
Ø150x 20mm
2950 rpm
36 / 60
10 kg
260W S1
1,5 A
max. 40W
3x1,5mm²
10A
I
Ø200x 25mm
2950 rpm
36 / 60
17 kg
370W S1
2,3 A
max. 37W
3x1,5mm²
10A
I