Garmin Fusion EL Série Instructions D'installation page 3

6
Place the speaker in the cutout to test the fit.
7
If necessary, use a file and sandpaper to refine the size of
the cutout.
8 After the speaker fits correctly in the cutout, ensure the
mounting holes on the speaker line up with the pilot holes on
the template.
9
If the mounting holes on the speaker do not line up, mark the
new hole locations.
10
Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
11 Remove the template from the mounting surface.
12 Connect the speaker wires
13
If necessary, connect the LED wires
14
Place the speaker in the cutout.
15
Secure the speaker to the mounting surface using the
included screws .
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
16
Attach the grille to the speaker front
page 3).
LED Wiring
Connecting the LED Wires
Before you connect the LED wires, you should determine which
speaker LED color you want to use, and identify the
corresponding speaker wire colors.
Speaker LED Color
Red
Green
Blue
Yellow
Magenta
Cyan
White
NOTE: This feature is available only on the sports model
speakers.
You can control the color of the speaker LEDs through the
polarity of the LED wires. You can splice the ground wire to
multiple wires on the LED cable to customize the LED color.
The black wire on the LED cable is terminated with a 4 mm
female bullet connector, and the color wires are terminated with
4 mm male bullet connectors. You can connect these to 4 mm
bullet connectors on your wires (not included), or remove the
bullet connectors to connect to the bare wires instead.
1
Connect a positive wire to the black wire on the LED cable.
Installation Instructions
while observing polarity.
(LED Wiring, page
(Attaching the Grille,
Speaker Wire Color
Red
Green
Blue
Red and green
Red and blue
Blue and green
Red, green, and blue
2
Connect a ground wire to the wire on the LED cable
according to the preferred speaker LED color.
3 Route the positive and negative wires, and connect them to a
power source
Wires to Power, page
Connecting the Sports Model Speakers LED Wires to Power
NOTE: This feature is available on only the Sports model
speakers.
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at
the power-source end of the cable. You should connect the
positive (+) power wire to a 12 Vdc power source through an
isolator switch or circuit breaker to turn the speaker LEDs on
and off. You can use the same isolator or circuit breaker
controlling the power supply to your stereo, which allows you to
turn the LEDs and the stereo on and off at the same time.
You should use 20 AWG (0.5 mm
the LEDs to the battery.
1
Route the positive power (+) and negative ground (-) wires
from the speaker to the battery.
2
Connect the negative wire to the negative (-) battery terminal.
3
Connect the positive wire to the positive (+) terminal through
a 3 A fuse and isolator switch or circuit breaker.
Attaching the Grille
1
With the speakers mounted, hold the grille with the FUSION
logo at the bottom, or at the 6 o'clock position.
2
Turn the grille counter-clockwise about 10 degrees, so the
FUSION logo is at the 5 o'clock position.
3
Place the grille on the speaker, and twist it clockwise to
3). secure it.
NOTE: You can press on the grille to snap it into place
instead of twisting it.
Speaker Information
Registering Your EL Series
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Dimension Drawings
Side View
40 mm (1
127 mm (5 in.)
A Sports model speaker is shown, but the dimensions are the
same for the Classic model.
(Connecting the Sports Model Speakers LED
3).
2
) or thicker wire to connect
37
/ in.)
64
3