Function Selection - Mitsubishi Electric City Multi PWFY-P100VM-E-BU Mode D'emploi

3. Function Selection

Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting when needed.
Item 1
1. Change Language Language setting to display
("CHANGE
LANGUAGE")
2. Function limit (1) Operation function limit setting (operation lock) ("LOCKING
("FUNCTION FUNCTION")
SELECTION")
(2) Operation mode skip setting ("SELECT MODE")
(3) Temperature range limit setting ("LIMIT TEMP FUNCTION")
3. Mode selection (1) Remote controller main/sub setting ("CONTROLLER MAIN/
("MODE SELEC- SUB")
TION")
(2) Use of clock setting ("CLOCK")
(3) Timer function setting ("WEEKLY TIMER")
(4) Contact number setting for error situation ("CALL.")
(5) Temp off set setting ("TEMP OFF SET FUNCTION")
(1) Temperature display °C/°F setting ("TEMP MODE °C/°F")
4. Display change
("DISP MODE
(2) Water temperature display setting ("WATER TEMP DISP
SETTING")
SELECT")
Function selection flowchart
[1] Stop the unit to start remote controller function selection mode. → [2] Select from item 1. → [3] Select from item 2. → [4] Make the setting. (Details are specified in item
3) → [5] Setting completed. → [6] Change the display to the normal one. (End)
Normal display (Display when
the unit is not running)
(Hold down the E button and press the D button for two
seconds.)
* The display cannot be changed during the test run and
the self diagnosis.
Item 1
Press the G button.
Change Language
("CHANGE LANGUAGE")
Press the
→ Operation function limit setting ("LOCKING FUNCTION")
E button.
Function limit
("FUNCTION
Press the
SELECTION")
G button.
Press the Press the
→ Remote controller main/sub setting ("CONTROLLER MAIN/SUB")
E button. E button.
Press the
Mode selection G button.
("MODE
SELECTION")
Press the
E button.
→ Temperature display °C/°F setting ("TEMP MODE °C/°F")
Press the
Display change G button.
("DISP MODE
SETTING")
Item 2
Remote Controller Function
Selection Mode
Item 2
Operation mode skip setting ("SELECT MODE")
Temperature range limit setting ("LIMIT TEMP FUNCTION")
Use of clock setting ("CLOCK")
Timer function setting ("WEEKLY TIMER")
Contact number setting for error situation ("CALL.")
Temp off set setting ("TEMP OFF SET FUNCTION")
Water temperature display setting ("WATER TEMP DISP SELECT")
• Display in multiple languages is possible
• Setting the range of operation limit (operation lock)
• Setting the use or non-use of each operation mode
• Setting the temperature adjustable range (maximum, minimum)
• Selecting main or sub remote controller
* When two remote controllers are connected to one group, one
controller must be set to sub.
• Setting the use or non-use of clock function
• Setting the timer type
• Contact number display in case of error
• Setting the telephone number
• Setting the use or non-use of setback amount setting
• Setting the temperature unit (°C or °F) to display
• Setting the use or non-use of the display of water temperature
(Hold down the E button and press
the D button for two seconds.)
* The remote controller records the
setting that is made in this way.
Press the
Press the G button.
D button.
Press the
D button.
Press the G button.
Press the
D button.
Press the G button.
Item 3 (Setting content)
NOTE
Timer operation stops when the display for
remote controller function selection is
changed to the normal one.
See [3]–1
Dot display
Item 3
The language that is selected in
(Setting content)
CHANGE LANGUAGE mode ap-
pears on this display. English is
See [3]–2. (1)
set in this manual.
See [3]–2. (2)
See [3]–2. (3)
See [3]–3. (1) F
TEMP.
See [3]–3. (2)
MENU
E
See [3]–3. (3)
BACK MONITOR/SET
PAR-W21MAA CLOCK
G
See [3]–3. (4)
See [3]–3. (5)
C
See [3]–4. (1)
See [3]–4. (2)
I
ON/OFF
A
ON/OFF INITIAL SETTING CIR.WATER
DAY CHECK TEST
CLEAR
B
D H
15