Specific Safety Rules - Makita DP3002 Manuel D'instruction

Masquer les pouces Voir aussi pour DP3002:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

14. Use safety equipment. Always wear eye protec-
tion. Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate con-
ditions. Ordinary eye or sun glasses are NOT eye
protection.
Tool Use and Care
15. Use clamps or other practical way to secure and
support the workpiece to a stable platform. Hold-
ing the work by hand or against your body is unsta-
ble and may lead to loss of control.
16. Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
17. Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
18. Disconnect the plug from the power source
before
making
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
19. Store idle tools out of reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
20. Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
Ampere Rating
More Than
0
6
10
12

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with
product (gained from repeated use)
replace strict adherence to drill safety
rules. If you use this tool unsafely or
incorrectly, you can suffer serious per-
sonal injury.
1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
any
adjustments,
Table 1. Minimum gage for cord
Not More Than
6
10
12
16
USB001-2
21. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may affect the tools operation. If damaged,
have the tool serviced before using. Many acci-
dents are caused by poorly maintained tools.
22. Use only accessories that are recommended by
the manufacturer for your model. Accessories
that may be suitable for one tool, may become haz-
ardous when used on another tool.
SERVICE
23. Tool service must be performed only by qualified
repair personnel. Service or maintenance per-
formed by unqualified personnel could result in a risk
of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unau-
thorized parts or failure to follow Maintenance
changing
instructions may create a risk of electric shock or
injury.
USE PROPER EXTENSION CORD: Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to
use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Volts
120 V
25 ft.
18
18
16
14
2.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3.
Hold the tool firmly.
4.
Keep hands away from rotating parts.
5.
Do not leave the tool running. Operate the tool
only when hand-held.
6.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
7.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
3
Total length of cord in feet
50 ft.
100 ft.
AWG
16
16
16
14
16
14
12
Not Recommended
150 ft.
14
12
12

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dp3003Dp4000Dp4001Dp4002Dp4003

Table des Matières