Euro-Pro Shark S3300 Guide D'utilisation page 4

OPERATING INSTRUCTIONS
Components
On/Off Power Switch:: The On/Off
switch has a light that will illuminate
when the unit is plugged into the 120V
wall outlet and the switch turned to the
"On" position.
Steam Ready Light: The steam ready
light located on the handle will turn "On"
when the steam is ready.
CAUTION:
Read the instructions for
"Filling the Water Tank" before opening
the Safety Cap.
CAUTION:
Always unplug before
filling. ALLOW UNIT TO COOL FOR
FIFTEEN (15) MINUTES BEFORE
REFILLING.
IMPORTANT:
Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the boiler in this
appliance. Use tap water or
distilled/purified water if the tap water
in your area is very hard.
Filling or Refilling Your Steam
Cleaner With Water
IMPORTANT:
Always insure that the unit
is "UNPLUGGED" from the wall receptacle
prior to initial filling or re-filling the water
tank and has been allowed to cool for 15
minutes. Never attempt to fill this unit
under a water tap, always use the filling
funnel provided.
1. Before filling or refilling the steam cleaner,
make sure that the unit is NOT plugged in
and has been allowed to cool for fifteen
(15) minutes.
2. Press the steam trigger on the hand grip
to vent any residual steam that is in the
boiler.
3. Place the unit on a flat, stable surface.
Push down firmly on the safety cap
and slowly turn the safety cap counter
clockwise until it is removed.
4. Place the funnel in the tank opening
(Fig. 1). Fill with a maximum of one filling
flask or 2 cups (500 ml) of water. Do Not
Overfill. Turn the safety cap clockwise to
replace.
NOTE: To remove or replace the safety cap,
push down on it firmly and rotate it clockwise
to tighten or counter clock-wise to loosen. If
not depressed the cap will rotate freely
without advancing.
NOTE: Filling the unit with hot water will
shorten the heat up time.
Fig. 1
WARNING:
Extreme care should be
taken when refilling the unit. Allow
unit to cool for 15 minutes before
refilling. When refilling the steam
cleaner while the boiler is still hot, there
is a risk that water will squirt back
during filling and cause scalding.
Extreme care should be taken when
refilling the unit. Use caution when
opening the Safety Cap as cap may
become hot during use and escaping
steam can cause scalding.
5. Connect desired attachments
onto the Flexible Steam Hose.
6. Plug the unit into a standard (120
volt, grounded) wall receptacle and
switch the On/Off switch to the "On"
position. Allow approximately 8-10
minutes for vapor to reach its
working temperature and pressure.
When the unit is ready for use, the
steam ready light will turn "On".
Always point nozzle outlet in a safe
direction. At the start, some water
will come out from the nozzle.
This is normal.
NOTE: When the steam cleaner has
run out of water, steam output will
cease.
7. When finished using the unit turn off
and unplug.
WARNING: This appliance is under
pressure. After every use, press steam
trigger button until all pressure has been
released before removing safety cap.
Allow unit to cool for fifteen (15) minutes
before refilling.
5
OPERATING INSTRUCTIONS
Using Your Steam Cleaner with
Steam Pocket
Step 1. Connect the steam pocket
accessory to the steam handle
with two extension tubes as
shown on page 8 (Fig. 10). To
attach the extension tubes one
onto the other or onto the hand
grip, press the locking button
ensuring that it fits 9into the hole
(Fig. 2., Fig. 3) and press the two
sections together. To disconnect,
repeat the operation by pressing
the locking button and pulling the
two sections apart.
Locking Button
Hand Grip
Hand Grip
Fig. 2
Fig. 3
NOTE:
Fit the steam pocket frame with
the angle adapter onto the extension
tube.
Step 2. If the angle adapter is not
attached to the steam pocket
frame, attach as follows: Hold
the steam pocket frame in one
hand and the
angle adapter in the
other. Insert the
angle adapter
steam into the
opening of the
steam pocket
frame as shown in Fig. 4. Note
that the flat on the nozzle must
face toward the side of the
frame with the brass pin. Once
inserted, rotate it 90°.
Step 3. Insert the electrical power cord
into the outlet. Heating time is
approximately 8-10 minutes with
cold water. Filling the steam
generator with hot water will
shorten the heat up time.
Attaching the Steam Pocket Towel
to the Frame
WARNING:
Always insure the unit is
"UNPLUGGED" from the wall receptacle prior
to attaching or removing accessories.
1. Slide the steam
pocket towel over
the steam pocket
frame. (Fig. 5)
Fig. 5
2. Bring the towel all
the way to the top
of the steam
pocket frame.
(Fig. 6)
3. Bring the velcro strips
that are on the
back side of the
steam pocket towel
over the steam pocket
frame and attach to
the inside of the
front side of the
steam pocket towel. (Fig. 7)
NOTE:
If replacing the steam pocket
towel, make sure that the steam pocket
frame has been allowed to cool before
removing or attaching a new steam
pocket towel.
Fig. 4
6
Fig. 6
Fig. 7