Box Content; Assembly - Greencut TOOLS881 Manuel D'utilisation

BOX CONTENT

-
6 Precision screwdrivers (-),1.0-1.4-1.8-1.8-2.4,(+) 01
-
9 Allen wrenches 1.5,2,2.2.5,3,4,5,6,8,10
-
24 Magnetic Bit Holder 25mm (-) 3,4,5,6,7, (+)
0,1,2,3,4,PZ1,2H3,4,5,6,7,8,T10,15,20,25,30,35
-
1 Handle with ratchet for screwdriver
-
1 Adapter 60mm
-
11 Screwdrivers (-) (+) 3*75.3*100, 6*75, 6*38,
6*100, (+) 6*150.
-
3 Screwdrivers for electrician (-) 4*100, 6-125, (+)
4*100
-
1 Electrical tester (pole-opener) 120-250 V
-
1 Extendable magnet 12, 5-63cm
-
1 Hexagonal tip Y
-
1 Cutting pliers
-
1 Wrench wrench
-
1 Parrot beak pliers
-
10 Mixed spanners 6,8,10,11,12,13,14,15,17,19mm
-
1 Long Point Pliers
-
1 Slip Joint Pliers
-
1 8OZ Nail Hammer
-
1 Tape measure 3m
-
120 Tacos
• Remove the product and accessories from the box. Make sure all items are present.
• Inspect the product to ensure that it has not been broken or damaged in transit.
• Do not discard the packaging material until you have carefully inspected and satisfactorily used the product.
ATTENTION: If any part is missing or damaged, contact the Official Technical Service. Do not use
this product without having replaced the missing or damaged part. Using this product with
damaged or missing parts can cause serious injury to the operator.

ASSEMBLY

BATTERY SCREWDRIVER
INSERTING TIPS
• Choose the tip that best fits the screw that will be adjusted or loosened. Place the tip inside the mandrel of
the screwdriver and make sure it is completely inside. The cordless screwdriver only takes tips with a 1/4 inch
hexagonal heads. Please note that it does not have the necessary speed to be used as a drill.
CHARGE
• The internal battery is not fully charged. Before its first use, the battery must be charged between 5 and 8 hours
in order for it to be fully charged. Thereafter, the charges will require between 3 and 5 hours for the battery to
be fully charged.
• Always recharge the internal battery when tool performance begins to decrease.
• Charge the internal battery at room temperature, between 50ºF (10ºC) and 95ºF (35ºC).
-
1 Set of 47 pieces: 1 ratchet wrench, 1 3/8 50mm
extension cord + 1 screwdriver handle + 1 3/8 cup
adapter to ¼ + 1 drop-proof cup + 10 screwdriver bits
(flat, star, torx) + 2 3/8 14 and 15mm cups, 2 3/8 11/16
and 5/8 cups, 14 ¼ cups from 4.5mm to 13mm and
14 ¼ cups of non-standard sizes (5/32, 3/16); 7/32, ¼,
9/32, 5/16, 11/32, 13/32, 3/8, 15/32, 7/16, ½, 17/32
y 9/16)
-
300 Screws
-
300 Nylon flanges
-
6 Drill bits for screwdriver 1.5/2/2.5/3/3/3.5/ 4mm
-
5 Hooks
-
1 Screwdriver 3.6V (Li-ion battery)
-
1 Charger for screwdriver
-
1 Adapter for electric screwdriver
-
1 Level
-
1 Nail hammer or carpenter's hammer
-
1 Cable crimping pliers
-
1 Cutter
-
1 measuring tape 2m
-
20 electrical terminals (for 0.25mm
23
EN
to 2.6mm cable)
2 2