Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TFA_No_30.3033_Anleit_8_sprach
MIAMI
– Wireless pool thermometer
2.2. Pool sensor (transmitter) Fig. 2
D1:
"TX" button
D2:
"°C/°F" button
D3:
Transmission indication LED
D4:
Water temperature
D5:
Water temperature sensor
D6:
For fastening rope
D7:
Screws battery compartment
3. Getting started
3.1 Insert battery
•
Place both instruments on a desk with a distance of approximately 1.5 meter. Check
that no other electronic devices are close.
•
Press and hold "TX" button and "°C/°F" button at the same time for 3 seconds to
switch on the transmitter. The current temperature and channel 1 are shown on the
LCD.
•
Insert the attached batteries (3x 1.5V AA) into the battery compartment of the display
unit, observing the correct polarity.
3.2 Reception of temperature transmitter
•
The display unit automatically starts scanning the 433 MHz signal to register the thermo
sensor unit after batteries are inserted. If the reception of outdoor values fails, "- -"
appears on the display. Check the batteries and try it again. Check if there is any source
of interference.
•
Manual initialization can be helpful. Hold "CHANNEL" button on the display unit for
3 seconds. The registered transmitter (channel) is canceled.
•
Press "TX" button on the transmitter. The display unit gives a "beep" sound if it re-
ceived the temperature.
4. How to operate
•
Important: Buttons will not function while scanning the outdoor temperature signal.
•
During operation, all successful settings will be confirmed by an acoustical signal.
•
The instrument will quit the setting mode, if there is no button used within 5 seconds
period.
•
Holding " " or " " buttons, you will enter fast mode.
4.1 Setting of clock and calendar
•
Hold "MODE" button for 3 seconds. The hour digit is flashing. Press " " or " " but-
tons to adjust hours. Using "MODE" button you can switch to setting minutes,
seconds, year, month/day sequence, month, day, time zone and day-of-week language.
10
04.06.2008
10:05 Uhr
Seite 6
MIAMI
– Wireless pool thermometer
•
In "month/day sequence" the two different date displays can be selected: Month/date
(American version) or date/month (European version).
•
Day-of-week language: English (EN), German (GE), French (FR), Spanish (ES), Italian
(IT), Dutch (NE), Danish (DA).
•
Choose 12 HR or 24 HR system by pressing the "
4.1.1 Indication of date
•
Press "MODE" button to show the date.
4.2 Alarm clock function
•
Select your desired alarm by pressing "MODE" button again:
1. Alarm 1
2. Alarm 2
•
Set the alarm time in the desired alarm mode. Hold "MODE" button for 3 seconds. The
hour digits are flashing. Press " " or " " button to adjust the time. Confirm with
"MODE" button. Set minutes in the same way.
•
To activate or deactivate the alarm function press "
alarm mode. "ON" or "OFF" appears on the display.
•
Once the alarm starts to ring, you can stop the alarm by pressing any button.
4.3. Thermometer
4.3.1 Change °C/°F
•
Press "
ALARM ON/OFF" button to select temperature display in Celsius mode or
Fahrenheit mode.
4.3.2 Trend pointer
•
The trend pointer displayed on the LCD indicates if the water temperature (channel 1)
is increasing, steady or decreasing.
4.3.3 Maximum/Minimum function
•
Press "MAX/MIN" button to show the maximum (MAX) temperature of the indoor
sensor and the selected outdoor transmitter. Press "MAX/MIN" button again to show
minimum (MIN) values.
•
Hold "MAX/MIN" button for 3 seconds to clear the recorded maximum and minimum
reading.
4.3.4 Temperature alert
•
Press "ALERT" button to set the temperature alert function on or off. (
the LCD if this function is on).
(12/24)" button.
AL ON/OFF" in the respective
appears on
11
Publicité
Table des Matières
