NEO HS2LCDWF Instructions D'installation page 2

Introduction
These instructions must be used with the appropriate control panel installation manual with which this
equipment is intended to be used. Operating instructions shall be made available to the user. The
HS2LCDWF wireless keypad is compatible with wireless transceivers HSM2HOST and
HS2LCDRF keypads.
Specifications
Temperature range: -10°C to +55°C (14°F to 131°F) UL/ULC: 0°C to +49°C (32°F to 120°F)
l
Humidity (MAX): 93%R.H. non-condensing
l
Plastic enclosure protection degree: IP30, IK04
l
Power adaptor output voltage: 9.0Vdc @ 1.25A. Models - US/Latin America: HK- XX11-
l
U09N (UL), Canada: HK- XX11-U09NC (ULC), EU: HK-XX11-U09EU, UK: HK- XX11-
U09NGB, AUS./NZ, China: HK- XX11-U09NAU limited power supply, acceptable to the
authority having jurisdiction.
Restraints are in place for UL installations.
l
This product is not to be connected to a receptacle that is controlled by a switch.
l
Battery: 4 AA, 1.5V, Energizer alkaline consumer-grade (E91)
l
Low Battery Indication: 4.5V
l
HS2LCDWF current draw: 30mA(min)/105mA(max)
l
Wall-mount tamper (connected when installed in UL commercial applications)
l
5 programmable function keys
l
Ready (Green LED), Armed (Red LED), Trouble/RF Jam (Red/Yellow), AC (Green)
l
Frequency: 433MHz (Brazil, China, Aus.(CE), NZ (NA), South Africa (ICASA), MEA, India
l
(WPC)
Frequency: 868MHz (EN + Local, MEA (CE))
l
Frequency: 912 - 919MHz (NA/LATAM, Argentina)
l
Dimensions (LxWxD): 168mm x 122mm x 25 mm
l
Weight: 370g (batteries included)
l
NOTE: For UL commercial installations, the tamper switches are enabled.
Unpack
The HS2LCDWF keypad package is available in three configurations. The keypad contains patented
technology for the Proximity (Prox) Tag.
HS2LCDWF - Wall Mount
1 HS2LCDWF wall bracket
1 installation manual
1 inner door sticker
4 AA batteries
1 hardware pack
HS2LCDWFPV - Prox Tag w/verbal annunciation
1 HS2LCDWF wall bracket
1 installation manual
1 inner door sticker
4 AA batteries
1 hardware pack
1 prox tag
HS2LCDWFP - Prox
1 HS2LCDWF wall bracket
1 installation manual
1 inner door sticker
4 AA batteries
1 hardware pack
1 prox tag
Mount the Keypad
Mount the keypad where it is accessible from designated points of entry and exit. Once a dry and
secure location has been selected, perform the following steps to mount the keypad.
Wall Mounting Plate
1. Locate the screw holes (4) at each corner of the mounting plate.
2. Use the four screws provided to affix the mounting plate to the wall; ensure the mounting tabs are
facing you (see following diagram). If the keypad is to be mounted on drywall, use plastic anchors.
3. Once the batteries are installed, align the four mounting slots in the HS2LCDWF housing with the
four mounting tabs protruding from the mounting plate.
4. Firmly but carefully snap the keypad down onto the mounting plate.
Desk Stand - HS2LCDWFDMK (Optional)
1. Insert the four rubber feet (found in the hardware pack) into the indentations provided in the bottom
of the desk stand.
2. Place the desk stand on a secure, uncluttered surface.
3. Align the four mounting slots in the HS2LCDWF housing with the four
mounting tabs protruding from the desk stand.
4. Slide the keypad into place. Firmly but carefully snap the keypad down
onto the desk stand.
5. To fasten the keypad securely onto the desk stand, locate the hole in
the center of the bottom of the desk stand. Using the screws provided,
screw the keypad to the desk stand.
Apply Battery Power
WARNING: If a low battery trouble signal is noted,the unit will operate
for a duration of no longer than 30 days. When a low battery trouble signal is noted, the batteries must
be replaced to ensure proper operation of the unit.
1. If required, slide the keypad up and out from the mounting plate/desk stand (removing the screws
first if required). The bay for the four AA batteries is open and visible at the back of the keypad.
2. Insert the batteries as directed on the back of the keypad. Ensure the correct polarity is observed.
3. Replace the keypad on the mounting plate/desk stand.
CAUTION: Do not mix old batteries with new ones.