Cequent Performance Products 41935 Instructions D'installation

Bumper bracket
Bumper bracket
Bumper
Bumper
Frame
Frame
Hitch Shown In Proper Position Hitch Shown In Proper
Equipment Required:
Equipment Required:
Fastener Fastener Kit: 41935F Kit: 41935F
Wrenches: 17mm, 19mm, 21mm
Wrenches: 17mm, 19mm, 21mm
Drill Bits: None
Drill Bits: None
Existing M12-l .25
Existing M12-1.25
bolts, (4) total.
bolts, (4) total.
Remove existing
Remove existing
brackets both sides.
brackets both sides.
Return to owner. Retum to owner.
1/2" Conical washer, toothed.
1 1 Qty. (4) Qty. (4) 1/2" Conical
2 2 Qty. (4) Qty. (4) M14-1.50 Flanged hex nut M14-I .50 Flanged
9/16" Helical lock washer
3 Qty. (8) 9/16" Helical
3 Qty. (8)
1. 1. Remove existing angle brackets, both sides, between truck frame rails and truck bumper brackets. Return to owner. Remove existing angle brackets, both sides, between truck frame rails and truck bumper brackets. Return to owner.
Save bolts as they Will be reinstalled in Steps 2 & 3.
Save bolts as they will be reinstalled in Steps 2 & 3.
2. Raise hitch into position as shown and reinstall M14 bolts removed in Step lthrough hitch and bumper bracket. Bolts must face
2. Raise hitch into position as shown and reinstall M14 bolts removed in Step 1through hitch and bumper bracket. Bolts must face
outwards as shown. Place 9/16" flat washers, lockwashers and M14 flanged hex nuts on these bolts on outside of truck bumper
outwards as shown. Place 9/16" flat washers, lockwashers and M14 flanged hex nuts on these bolts on outside of truck bumper
bracket. Hand tight only.
bracket. Hand tight only.
3. Place a toothed conical washer over each M12 bolt removed in Step 1, and then reinstall M12 bolts through hitch and into
3. Place a toothed conical washer over each M12 bolt removed in Step 1, and then reinstall M12 bolts through hitch and into
weldnuts in truck frame. Hand tight only. weldnuts in truck frame. Hand tight only.
Install M14-1.50 bolts supplied through 9/16" helical lockwashers and blocks. Install these through hitch and then through blocks
4. 4. Install M14-I .50 bolts supplied through 9/16" helical lockwashers and blocks. Install these through hitch and then through blocks
into frame weldnuts, typical (4) places. Hand tight only. into frame weldnuts, typical (4) places. Hand tight only.
5. 5. If existing electrical bracket on bottom of truck bumper contacts top of hitch tube, then bend up out of the way. It may be If existing electrical bracket on bottom of truck bumper
necessary to cut bolts holding electrical bracket shorter so that bracket can be pushed up farther. necessary to cut bolts holding electrical
6. Torque M12 bolts to specifications below first. Then torque M14 bolts in bumper brackets to specifications below next.
6. Torque M12 bolts to specifications below first. Then torque M14 bolts in bumper brackets to specifications below next.
Torque M14 bolts forward on frame to specifications below last.
Torque M14 bolts forward on frame to specifications below last.
Torque all MI 2 fasteners with torque wrench to 130 lb.-Ft.(176 N *M)
Torque all M12 fasteners with torque wrench to 130 lb.-Ft.(176 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V. E.S.C. Regulation V -5
and SAE J684.
and SAE J684.
z
z 2007, 2012 Cequent 2007, 2012 Cequent Performance Products Performance
Installation
Installation Instructions
Toyota Tundra
Toyota Tundra
o o
Position
Existing MI 4-1.50
Existing M14-1.50
bolts, (4) total.
bolts, (4) total.
washer, toothed.
hex nut
lock washer
bracket shorter so that bracket can be pushed up farther.
Products
Instructions
Do Not Exceed Lower of Towing Vehicle Do Not Exceed Lower of Towing Vehicle
Hitch type
Hitch type
Weight Distributing Weight Distributing
Weight Carrying
Weight Carrying
Ball Mount
Ball Mount
Wiring
Wiring Access Location: PU3
Existing weldnuts
Existing weldnuts Place
Place blocks
in frame
in frame outside
outside of frame and hitch.
1 1
9/16" Flat washer
Qty. (4) Qty. (4) 9/16"
4 4
5 5 Qty. (4) Qty. (4) M14-1.50 X 45mm Cl. 10.9 Hex bolt M14-1.50
1/4" X 1-1/2" X 2" Block
Qty. (8) 1/4"
6 6 Qty. (8)
contacts top of hitch tube, then bend up out of the way. It may be
Torque all M14 fasteners with torque wrench to 148 lb.-Ft. (201 N *M)
Torque all M14 fasteners with torque wrench to 148 lb.-Ft. (201 N*M)
Sheet 1 of 3 Sheet 1 of 3
Part Part Numbers:
UHI41936 UH141936
Manufacturer's Rating or
Manufacturer's Rating or
Max Gross
Max Gross
Trailer WT- 1b (Kg)
Trailer WT- lb (Kg)
14,000 (6356)
14,000 (6356)
12,000 (5448)
12,000 (5448)
Access Location: PU3
6 6
blocks between
between
of frame and hitch.
ALL FASTENERS ALL
TYPICAL TYPICAL BOTH SIDES.
ooo
3
2 4
Flat washer
X 45mm Cl. 10.9 Hex bolt
X 1-1/2" X 2" Block
41935N 41935N 6-1-12 6-1-12
Form: Form: F205 Rev A 5-6-05
Numbers:
41935 41935
96935 96935
Max Tongue
Max Tongue
WT- 1b (Kg)
WT- lb (Kg)
1400 (636)
1400 (636)
1200 (545)
1200 (545)
FASTENERS
BOTH SIDES.
ooo
3
6
5
Rev. C Rev. C
F205 Rev A 5-6-05