Cequent Performance Products 24759 Instructions D'installation
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
Frame
Hitch Shown In Proper Position
Hitch
Shown In Proper
Equipment
Required:
Equipment Required:
Fastener
Kit:
24759N
Fastener Kit: 24759N
Wrenches: 3/4", 15mm, 17mm
Wrenches:
3/4", 15mm,
Drill Bits: 1/2"
Drill
Bits:
1/2"
Screwdriver
Screwdriver
Taillight
Taillight
access
access
2
2 Typical b othsides
1
1
Typical both sides
j
1/2"-13 X 1-3/4" Carriage bolt
Qty. (2)
Qty. (2)
1/2"
-13 X 1-3/4" Carriage
k
1/4" X 1-1/2" X 2" Block
Qty. (2)
1/4 " X 1-1/2"
Qty. (2)
l
1/2" Lock washer
Qty. (2)
Qty. (2)
1/2"
Lock
washer
1.
Remove tow hooks if present. Return tow hooks & fasteners to owner.
1.
Remove tow hooks if present. Return tow hooks & fasteners to owner.
2.
Remove both taillights by removing screw at bottom of light cover.
2.
Remove both taillights by removing screw at bottom of light cover.
3.
Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler.
3.
Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler.
4.
Position hitch as shown and install MIO fasteners provided.
4.
Position hitch as shown and install M10 fasteners provided.
Using hitch as a template, drill 1/2" holes in (2) places.
Using hitch as a template, drill 1/2" holes in (2) places.
5.
5.
6.
Fishwire carriage bolt and block through access holes in taillight openings, as shown.
6.
Fishwire carriage bolt and block through access holes in taillight openings, as shown.
7.
Torque all fasteners to specifications
7.
Torque all fasteners to specifications shown below.
8.
Re-install exhaust hangers and taillights.
8.
Re-install exhaust hangers and taillights.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
and SAE
1684.
z
2005, 2015 Cequent
Performance
2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation
Installation Instructions
Chrysler
Chrysler PT Cruiser
Bumper
Bumper
(Sold separateli)
(Sold separately)
Drawbar
Drawbar Kit:
Drawbar
Drawbar must be used in the
o
RISLposition
RISE position only.
Position
17mm
bolt
X 2" Block
shown below.
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
Tighten all MI 0 CL8.8 fasteners with torque wrench to 38 Lb.-Ft.
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft.
Products,
Inc. - Printed in Mexico
Instructions
PT Cruiser
Kit:
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
3593
3593
must be used in the
2000 LB Max Gross Trailer Weight
2000 LB Max Gross Trailer Weight
only.
200 LB Max Tongue Weight
200 LB Max Tongue Weight
Wiring
Wiring Access Location: SUV 1, SUV 2
Frame
rails
Frame rails
Existing weld nuts,
Existing weld nuts,
Typical both sides
Typical both sides
Drilled
holes
Drilled holes
both
sides
both sides
4
4
3 Typical both sides
3
Typical both sides
m
O
Qty. (2)
Qty. (2)
n
Qty. (4)
Qty. (4)
o
Qty. (4)
Qty. (4)
Sheet 1 of 3
Sheet
I of 3
Manufacturer's Rating or
Manufacturer's
Rating or
Access Location:
SUV l, SUV 2
Position blocks
Position
as shown
as shown
5
6 Typical both sides
5
6
Typical both sides
1/2" Hex nut
1/2"
Hex
nut
MIO
X 1.50
X 35mm
CL8.8
Hex
M10 X 1.50 X 35mm CL8.8 Hex bolt
3/8" Conical washer
3/8"
Conical
washer
24759N
24759N
10-13-15
10-13-15
Part Numbers:
Part Numbers:
24759
24759
77135
77135
60818
60818
blocks
bolt
Rev. B
Rev.
B
Manuels Connexes pour Cequent Performance Products 24759
Sommaire des Matières pour Cequent Performance Products 24759
- Page 1 SAE J684. and SAE 1684. 2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico Sheet 1 of 3 Sheet I of 3 24759N 24759N 10-13-15 10-13-15 Rev. B Rev. 2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. d ' attelage. 2005, 2015 Cequent Performance Products, Inc. Impriméau Mexique Feuille 2 de 3 Feuille 2 de 3 24759N 24759N 10-13-15 10-13-15 Rev. B Rev. 2005, 2015 Cequent Performance Products, Inc. Imprimé au Mexique...
- Page 3 Nueva York. V.E.S.C. Regulació n V-5 y SAE J684 2005, 2015 Cequent Performance Products, Inc. - Impreso en Mé(ico Hoja 3 de 3 Hoja 3 de 3 24759N 24759N 10-13-15 10-13-15 Rev. B Rev. 2005, 2015 Cequent Performance Products, Inc. - Impreso en México...