Kenwood KCA-RC35MR Mode D'emploi

FCC WARNING :
This equipmentmay generateor use radio frequencyenergy.Changes
or to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could losethe authorityto operatethié equipnmt if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to corply with the limits for a
Class B digitaldevice, pursuantto Part 15 of the FCC Rules.These
limits are designedto providereasonableprotectionagainst harmful
interference in a residential installation. This equipment may cause
harmful interference to radio communications,
used in accordance with the instructions. However, there is no guarantee
that interference will not occur in a particular installation.
If this equiprnent does cause harmful interference to radio or television
reception, which can be determined by turning the equiprnent off and.on,
the user is encouraged to try to correct the interference by one or more
Of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING
(I)THIS DEVICEMAYNOT CAUSE HARMFULINTERFERENCE, A ND
(2)THlS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
NOTICE:
This Class B digital apparatus corrplies with Canadian ICES-003.
REMARQUE:
Cet appareil numéique de la classe B est conforme å la norme NMB-003
du Canada.
.English
Function and Operation
8
3
7
Source Select
2. Seek +
3. Seek -
4. up (FM)
Before Installation
AWARNING
It you connectthe ignitionwire (red) and
the illumination wire (orange) to the
negative ground point, you may cause a
short circuit, that in tum may start a fire.
Always connect those wires to the power
source running through the fuse box.
• This unit is designed for marine use.
• Mounting and wiring this product
requires skill and experience. For safety
reasons leave the mounting and wiring
work to professionals.
• Make sure to ground the unit to a
negative 12V DC power supply.
• Do not install the unit in a spot exposed
to direct sunlight or excessive heat and/or
humidity.
• Do not use your own screws. Use only
screws provided. If you use the wrong
screws you could damage the unit.
if it is not installed and
MO CONDITIONS:
4
6
2
1
5
5. Down (AM)
6. Volume Up
7. Volume Down
8. Mute / Pause
• If your vessel ignitiondoes nothave an
ACC protection, connect the ignition wire
to a power source that can be turned on
and off with the key or other control
switch. If the receiver is left on for an
extended period of time the battery may
die.
• If the fuse blows, first make sure the
wires aren't touching to cause a short
circuit. Then replace the old fuse with one
of the same rating.
• Insulate unconnected wires with vinyl
tape or other similar material. To prevent
a short circuit do not remove the caps on
the ends of the unconnected wires or the
terminals.
• After installing the unit, check to make
sure that electrical equipment such as the
signal lamps and gauges operate
normally.
KENWOOD
KCA-RC35MR
REMOTE CONTROL
INSTRUCTION
UNITÉ DE TÉLÉCOMMANDE
MODE D'EMPLOI
UNIDAD DE CONTROL
MANUAL DE INSTRUCCIONES
JVC KENWOOD Corporation
US Resident Only
Register Online
Register your Kenwood product at
www.Kenwoodusa.com
Installation
1. Set the gasketto the placewhere the KCA-RC35MRis to be installed
and pierce with a drill bit for wiring harness and the installation.
2. Fix the KCA-RC35MR as shown in figure.
Nutt
Lock Washer
Washer
Bracket
Connection
KCA-RC35MR
o
Rernote Control
Output
(Light Blue/Yellow)
Ignition Wire
(Red)
Illumination Wire
(Orange)
Ground Wire (Black)
To a negative ground point of the vessel
UNIT
MANUAL
REMOTO
Mounting Surface
Gasket
KCA-RC35MR
Remote Control Input
(Light Blue/Yellow)
CD - Receiver
Ignition Key Switch
Fusebox
ACC
Illumination
Control SW
Fuse box
(Main Fuse)