Ryobi AC04150T Mode D'emploi

A WARNING:
WaRning:
To reduce the risk of injury, user must read and understand
To reduce the risk of injury, user must read and understand
the operator's manual for their tool. Always wear safety
the operator's manual for their tool. Always
glasses.
glasses.
installing stRing head
INSTALLING STRING
See Figures 1 - 2.
See Figures I - 2.
 Stop the engine and disconnect the spark plug wire.
Stop the engine and disconnect the spark plug wire.
 Remove currently installed string head.
Remove currently installed string head.
 Open the Reel Easy String Head by depressing the latches on
Open the Reel Easy String Head by depressing the latches on
each side. The contents of the string head are spring loaded,
each side. The contents of the string head are spring loaded,
so keep your other hand over the string head cover while de-
so keep your other hand over the string head cover while de-
pressing the latches.
pressing the latches.
 Remove the string head cover, knob, and spool and set
Remove the string head cover, knob, and spool and set
aside.
aside.
 Place the string head on the drive shaft. Make sure the string
Place the string head on the drive shaft. Make sure the string
head is fully seated.
head is fully seated.
 Install the hex bolt into the opening on the drive shaft and secure
Install the hex bolt into the opening on the drive shaft and secure
using the hex-shaped opening in the knob to tighten. Use the
using the hex-shaped opening in the knob to tighten. Use the
black bolt if installing on a curved shaft trimmer or silver bolt if
black bolt if installing on a curved shaft trimmer or silver bolt if
installing on a straight shaft trimmer or brushcutter.
installing on a straight shaft trimmer or brushcutter.
nOte: Only use the knob to tighten the bolt. The use of other
NOTE: Only use the knob to tighten the bolt. The use of other
tools may allow overtightening of the bolt, which could damage
tools may allow overtightening of the bolt, which could damage
the string head.
the string head.
nOte: For the brushcutter, the gear head locking tool can be
NOTE: For the brushcutter, the gear head locking tool can be
inserted through the slot in the flanged washer and gear head
inserted through the slot in the flanged washer and gear head
to help hold the string head still.
to help hold the string head still.
 If removed, replace the spring into the string head and push
If removed, replace the spring into the string head and push
down to seat.
down to seat.
 Reinstall the spool. For curved shaft trimmers, the spool should
• Reinstall the spool. For curved shaft trimmers, the spool should
be placed so "This side out for curved shaft" is visible. For
be placed so "This side out for curved shaft" is visible. For
straight shaft trimmers or brushcutters, the spool should be
straight shaft trimmers or brushcutters,
placed so "This side out for straight shaft" is visible.
placed so "This side out for straight shaft" is visible.
 Replace the knob in the spool.
• Replace the knob in the spool.
 Replace the string head cover, aligning latches with openings
Replace the string head cover, aligning latches with openings
in the string head. Press cover and string head together until
in the string head. Press cover and string head together until
both latches snap into openings securely.
both latches snap into openings securely.
 Install string as described in the next section.
Install string as described in the next section.
installing stRing
INSTALLING STRING
See Figure 3.
See Figure 3.
Use .095 in. diameter monofilament string.
Use .095 in. diameter monofilament string.
 Stop the engine and disconnect the spark plug wire.
Stop the engine and disconnect the spark plug wire.
 Cut one piece of string approximately 25 ft. in length.
Cut one piece of string approximately
 Rotate knob on string head until line on knob aligns with arrows
Rotate knob on string head until line on knob aligns with arrows
on top of string head.
on top of string head.
 Insert one end of string into eyelet located on the side of the
• Insert one end of string into eyelet located on the side of the
string head and push until string comes out through eyelet on
string head and push until string comes out through eyelet on
the other side. Continue to push string through the string head
the other side. Continue to push string through the string head
until the middle section of the string is inside the string head
until the middle section of the string is inside the string head
and string outside the string head is evenly divided on each
and string outside the string head is evenly divided on each
side.
side.
 Rotate the knob on the string head to wind the string. If using a
Rotate the knob on the string head to wind the string. If using a
curved shaft trimmer, knob should be rotated counterclockwise.
curved shaft trimmer, knob should be rotated counterclockwise.
If using a straight shaft trimmer or brushcutter, knob should
If using a straight shaft trimmer or brushcutter, knob should
be rotated clockwise. Wind the string until approximately
be rotated clockwise.
8 in. remains protruding from the string head.
8 in. remains protruding from the string head.
Reel easy stRing head
REEL EASY
aC04150t
AC04150T
wear safety
HEAD
the spool should be
25 ft. in length.
Wind the string until approximately
STRING HEAD
StraIGht
STRAIGHT
ShaFt
SHAFT
o
o
cUrved
CURVED
ShaFt
SHAFT
0
hex-ShaPed
HEX-SHAPED
oPenInG
O PENING
aLIGn
ALIGN
LIne on
LINE ON
knob wIth
KNOB WITH
arrowS
ARROWS
For futher installation instructions,
For futher
see chart on back page.
see chart on back page.
Latch
LATCH
oPenInG
OPENING
hex boLt
HEX BOLT
StrInG to
STRING
and rotate
AND ROTATE
installation instructions,
cover
COVER
LatcheS
LATCHES
knob
KNOB
hex boLt
BOLT
SPooL
SPOOL
SPrInG
SPRING
StrInG
TRING
head
HEAD
Fig. 1
Fig. 1
knob
knob
KNOB
Fig. 2
Fig. 2
InSert
INSERT
TO
center
CENTER
knob to
KNOB TO
wInd
WIND
eyeLet
EYELET
Fig. 3
Fig. 3