Télécharger Imprimer la page

AOSHIMA Lamborghini Countach 5000 Quattrovalvole Injection Ver. Mode D'emploi

Liens rapides

'24
SUPER
CAR SERIES
COUNTACH
5000
QUATTROVALVOLE
INJECTION
Ver.
(OVERSEAS
EDITION)
AOSHIMA
Important
Information
to be Read before Assembling
• This model needs to be assembled. Read the assembly instructions before beginning to
assemble
it.
• After taking the product out of the plastic bag, tear the plastic bag and discard it. since there
will be a danger of suffocation if young children place the bag over their head.
Cleanly clip the parts from the trees, and discard the trees after all the parts have been
clipped.
Due to manufacturing circumstances it is unavoidable that there will be sharp places which
will be dangerous. Be sure not to play with the contents such as by using them for other
purposes. Households with young children should be particularly careful.
• Use nippers for removing parts, and finish any burr remaining on parts using a knife or file.
Because
the mishandling
of nippers, cutter knives or files may result in sharp edges cutting
hands, fingers, or legs, children younger than 14 years old should have the work carried out
by a parent or guardian.
As the kit contains
small parts. take care not to swallow them by mistake,
a danger of choking. Due to the danger of mistakenly swallowing parts, be absolutely certain
not give them to children younger than the target age.
(In the situation where you use cement or paints, take care of the following points)
Do not put cement or paint in your mouth, since there will be a danger of poisoning.
If cement or paint gets in your eyes, immediately wash it away with a large amount of water
and consult
a doctor.
Do not use cement or paint in enclosed rooms. since there will be a danger of poisoning.
Absolutely do not use cement or paint near sources of flame, since there will be a danger of
ignition.
Do not leave the product in locations subject to direct sunlight or in places with high
temperatures
or much humidity.
Information
importante
Ce modöle doit étre assemblé, Lisez les instructions de montage avant de commencer '"assemblage.
Apres déballage du kit veillez å vous débarrasser des sacs en plastique pour eviter tout risque
détouffernent
des enfants en bas age qui pourraient les placer sur leur téte.
• Détachez soigneusement les branches d'arbres, et jetez les déchets.
En raison des conditions de fabrication, certaines pieces possedent des parties pointus qui peuvent
étre dangereuses. S'assurer de ne pas jouer avec le contenu en rutilisant pour d'autres buts. Les
familles ayant des enfants en bas age devront faire trés attention.
Utilisez une pince Coupante pour dégrapper les pieces, et éliminez toutes les bavures résiduelles sur
les piéces
"aide d'un couteau de modéllsme ou d'une lime Putsqu'une manipulation Incorrecte des
pinces, des couteaux de modélisme ou des limes Peut se produlre. il y a risque de blessure des
mains, des doigts ou des jambes, les enfants de moins de 14 ans devront demander a leurs parents
ou leur gardien d'effectuer les travaux.
Ce kit contient de petites pieces, ne convient pas a des enfants en-dessous de Page prevu pour
l'usage de ce produit: risque d'étouffernent. Du fait d'un risque d'étouffement. soyez absolument sür de
ne pas les donner aux enfants plus jeunes que l'åge prévu pour l'usage de ce produit.
Lorsque
vous utilisez
de la colle et des pe•ntures.
La colle et les peintures ne doivent pas étre ingérées, car i' y a risque d'empoisonnement_
Si la colle ou les peintures entrent en contact avec les yeux, lavez avec une grande quantité d'eau et
contactez
immédiatement
un docteur_
N'utilisez pas la colle ou les petntures dans des endroits fermés. car il y a risque d'empoisonnement,
veillez
travailler dans un endroit bien ventilé ou pros dune fenétre ouverte.
N 'utilisez pas la colle ou les peintures pres de sources de Chaleur ou d'une flamme, car il y a risque
dincendie.
Ne laissez pas ce produit dans des endroits exposés directement å la lumiére du soleil ou dans des
endroits
forte température Ou humides.
AOSHIMA
BUNKA
1/24 SCALE MODEL KIT
Lamborghini
5000
Quattrovalvole
Injection
Ver.
this Product
since there may be
å lire avant de monter ce modéle :
suivez attentivement
les points suivants
KYOZAI
co.
Ltd.
Countach
Informazioni
importanti
• Questo modellodeve essere assemblato.Leggere le istruzioniprima di iniziare il montaggio.
• Dopo aver estratto il prodotto dal sacchetto di plastica, strappare il sacchetto e buttarlo,
poiché ci potrebbe essere pericolo di soffocamento se i bambini piccoli 10mettessero in testm
• Tagliarebene ognupezzo dalla materozzaed una volta tagliati tutti i pezzi buttare la
materozza.
• A causa di circostanzedi produzione,e inevitabile la presenza spjgolivivi che potrebbero
essere pencolosi. Nongiocarecon il contenuto della scatola per altri scopi. Le famiglie con figli
piccoli pongano particolare attenzione.
• Utilizzaretronchesineper il taglio e pulire qualsiasi sbavaturaresidua sui pezzi con una lama
o una lima.
Poiché l'inappropriatoutilizzodi tronchesine, lame o lime pub provocarespigoli vivi taglienti
per mani, dita e gambe, i bambinidi eta inferiore a 14 anni devonoessere assistitidurante il
lavoro da un genitore o.comunque. da un adulto.
• Poichéil kit contiene piccole parti. fare attenzionea non ingerirle per errore poichéci
potrebbe essere pericolo di soffocamento. A causa del rischio di ingestione di piccole parti,
accertarsl assolutamente di non darle in mano ai bambini di etå inferiore a quella indicata
• (Nel caso in cui si utilizzinocolle o vernici, prendere nota dei seguenti punti).
Non ingerire colle o vernici poiché ci potrebbeessere rischio di avvelenamento.Se colle o
vernici dovessero venire in contatto con gli occhi, Iavarli immediatamente con abbondante
quantita d'acqua e consultare il medico.
Non utilizzare colle o vernjci in ambienti chiusi poiché ci potrebbe essere pericolo di
awelenamento.
Non utilizzare assolutamentecolle o vernici vicino a fonti di calore o fiamme poichéci potrebbe
essere
nschio
di incendio.
• Non lasciare il prodotto in luoghi esposti alla luce diretta del sole o in luoghi con temperature
elevate o molto umidi.
Wichtige
Information
• Dieses Modell muss montiert werden. Lesen Sie vor der Montage die Montageanweisungen
• Nach dem Entfernen der Telle des Modellsatzes reißen Sie die Plastikverpackungstüte
verhindern, dass kleine Kinder damit spielen und Sie sich über den Kopf ziehem dabel besteht
Erstckungsgefahr
• LOsen Sie die Bausatzteile vorsichtig aus den Spritzlingen und entsorgen Sie den Abfall.
Herstellungsbedingt
können, Stellen Sie sicher. den Inhalt nicht zu anderen als den vorgesehenen Zwecken zu verwenden.
Bausatze wegen verschluckbarer Kleinteile außerhalb der Reichwe•te von Kindern aufbewahren.
• Verwenden Sie etne Kneifzange zum Entfernen von Tellen und entfernen Sie Grate mit einem Messer
Oder einer Feile, Durch falschen Umgang mit Kneifzangen, Schneidmessern Oder Feilen können
scharfe Kanten mit Verletzungsgefahr entstehen. Daher nicht geelgnet für Kinder unter 14 Jahren und
nur unter Aufsicht
eines edahrenen
• Der Bausatz enthält verschluckbare Kleintelle. Es besteht Erstickungsgefahr! Bewahren Sie die Teile
daher außerhab
der Reichweite
• Bei Verwendung von Klebstoffen und Lacken achten Sie auf die folgenden Punkte:
Klebstoffe und Lacke dürfen nicht verschluckt werden, da Vergiftungsgefahr besteht.
.
Falls Klebstoffe Oder Lacke in die Augen geraten. sofort mit viel fließendern Wasser ausspülen und
anschl.eßend
e.nen
Arzt
Klebstoffe und Lacke dürfen nicht an geschlossenen Orten verwendet werden. da beim Einatmen
Vergiftungsgefahr besteht.
Klebstoffe
und Lacke ddr-fen nicht in der Nåhe offener
Entzündungsgefahr
besteht
Legen Sie das Produkt nicht im direkten SonnenlichtOderan Orten mit hohenTemperaturenOder
Luftfeuchtlgkeit ab.
12-3 RYUTSU CENTER,
AOI-KU, SHIZUOKA
da leggere prima di assemblare il modello
vor dem Montieren
dieses Modellbausatzes:
ist eS unvermeidlich. dass es scharfkantige Stellen gibt. die gefahrlich sein
Erwachsenen.
von Kindern
auf,
aufsuchen.
Flammen
ver-wendet
CITY, SHIZUOKA
durch.
auf. um zu
werden,
da
420-0922,
JAPAN
loading

Sommaire des Matières pour AOSHIMA Lamborghini Countach 5000 Quattrovalvole Injection Ver.

  • Page 1 Lamborghini Countach (OVERSEAS EDITION) 5000 Quattrovalvole Injection Ver. AOSHIMA Important Information to be Read before Assembling this Product Informazioni importanti da leggere prima di assemblare il modello • This model needs to be assembled. Read the assembly instructions before beginning to •...
  • Page 2 How to use window masking seal 1. Peel off the wondow maskingseal from the sheet and apply it on the back of the window part. Frostedtrim is the guide for right position. Make sure the window mask is firmly applied otherwisethe paint bleeds underthe edge of it. 2.
  • Page 3 ( Painting / Verniciatura • AQUEOUS HOBBY COLOR and Mr. Color are not mixable. FarbenundKlebstoffefür Plastikmodellemüssengetrenntgekauftwerden. • HOis thecolornumber o fAQUEOUS HOBBY COLOR ofGSI C reos C orporation WeitereEinzelheitenüber die VerwendungderWerkzeugeund Lackesiehe • the color number of Mr. Color of GSICreosCorporation Erklärungen auf dem betreffenden Produkt.
  • Page 4 Usethe photo-etchedparts and metal stickersto your preference.Moreoveryou can give even furtherdetailsto the model by using "Lamgorghini Countach common detail up parts set" (available sepearately, retail price JPYI ,500-). Lamborghini Countach 1500 am Fotoätzteile und Metallaufkleber nach Wunsch benutzen. Mit dem "Lamborghini Countach common detail-up set" können nogh mehr Details realisiert werden.
  • Page 5 (a little ) Adjust the mixing rate to achieve Semi Gloss Black. Poly cap Mozzo in polietilene Tire (smaller) Pneumatico (stretto) Slight overlayer with 'gives more realistic finish. Poly cap Mozzo in polietilene Fix it first. D D'ao...
  • Page 6 Poly cap Mozzo in polietilene Tire (bigger) Pneumatico (largo) Poly cap Mozzo in polietilene Slight overlayer on with 8 gives more realistic finish. Rear side...
  • Page 7 Meterdecal@ hasglue on printedside. Les autocollants@ comportentde la colle sur le cöté imprimé Decals@ Ait der bedrucktenSeite autkleben. Front side Le decalsu hanno la colla sul lato stampato Meter trim (Parts position in the engine bay) Wider...
  • Page 8 Partsuis "A pillar support" only used in certain assembly sequence. Attach it to the designated area with using re-peelable tape or cut out extra part of the masking seal included. A pillars Colore carrozzeria Body Note direction „'iHfifi Front light glass Front light glass Note the direction...
  • Page 9 PH(121 16 PHO Front side...
  • Page 10 Mirror Remove(f) from thebody. Note no glue in this area Diese Stelle nicht kleben Ne pas coiler cette partie Fix the rear side first. Fit them without gluing Teile ohne Kleber positionieren Montez les sans collage Door R In order to achieve optimum gluing of (68)&(69), build them with the door in closed position and fix them with re-peelable tape on the body, then glue them on the body.
  • Page 11 Door Door (opened position) Shaft (short) Door (closed position) [00$) Insert the door in this hole for opened position Working engine hood can be held open by using the shaft (long) To fix the finished model onto a display base, Tür in diesem Loch positionieren, use (33) and screw it from the back of the base.
  • Page 12 Aventador LP700-4 Roadster Murcielago LP670-4 SV Aventador LP700-4 Pleasecontact your local Aoshima Dealersfor prices and/or availability; or you may find what you are looking for at http://www.aoshima-bk.co.jp/english/ Perprezziefodisponibilitåsi pregadi contattareil vostro negoziodi fiducia o potetetrovarequello chestatecercandoalseguentelink: http://www.aoshima-bk.co.jp/english/ 2015. IONE -12-...

Ce manuel est également adapté pour:

18