Télécharger Imprimer la page
Les langues disponibles

Les langues disponibles

Liens rapides

-naäuC7$
STOP
1) Remove jack from box.
2) Turn the jack clockwise
completely
extend the jack to its
highest
position.
3) Remove the black 3/8" Adapter
4) Separate the two tubes so the large threaded
5) Use a high viscosity
gear lubricant
lubricated
and ready to be reassembled
6) After installation,
manually
the rod. Jack is now ready for use.
Product
Satisfaction
At Extreme Max, we pride ourselves on making quality products and wish to correct any mistakes on our end. If you are
not 100% satisfied
With the product, for any reason, please reach out to us. We are here to help!
Warranty
This product is warranted
for consumer
Warranty
valid
only in the USA.
This product
is warranted
to the original
wear and tear expected.
This warranty
ofgood
s
oranyacts ofvandalism
commercial
use. The sole remedy
or similar
product, or the refund of the original
incidental
damages. Any and all freight charges to handle warranty
MaxTM is not responsible
for any labor charges that may be incurred.
For all inquries please send your name, mailing
summary
of alleged defect and any applicable
Customer Service: service@extrememax.com
Snow
Assembly
Before assembling
your snowmobile
you MUST properly
lubricate
Failure to properly
lubricate
void the warranty.
to
by removing
the bolt at the base.
rod is exposed.
to generously
and installed
cycle jack twice without
Guarantee
use for 2 years after the date of retail purchase. Warranty
retail
purchaser
shall not ap ly to any defects caused by: (l) overloading,
byany person, (PII) improper installation
under
this warranty
is at the discretion
purchase price. Extreme MaxTM is not responsible
address, main contact phone number,
pictures to service@extrememax.com.
Pro
Snowmobile
Instructions
lift
your jack.
the jack will
lubricate
the entire threaded
on the lift.
load to insure that lubricant
to be free from
defects
in material
oruse contrary totheinstructions,
of manufacturer:
claims are the responsibility
I www.extrememax.com
Lift
5800.1045
- W/O
Wheel
5800.1066
- W/
Wheel
rod. Jack is now
travels all the way to
includes
parts only.
and workmanship,
ordinary
(II) physical abuse
(IV)
the replacement
of the same
for any consequential
of the consumer.
original
retail sales receipt,
Kit
Kit
or
Extreme
3518ex0121
loading

Sommaire des Matières pour Extreme Max 5800.1045

  • Page 1 Satisfaction Guarantee At Extreme Max, we pride ourselves on making quality products and wish to correct any mistakes on our end. If you are not 100% satisfied With the product, for any reason, please reach out to us. We are here to help!
  • Page 2 Includes: • Heavy Duty 5,000 lb. Jack • Rubber Lift Cushions •31" Lift Height • Durable Automotive Red Powder Coat Finish • Grade 5 Hardware • Lifts Sled Evenly and Quickly • 5-1/2" Collapsed Height • Two Year Full Replacement Warranty •...
  • Page 3 å la tige. Jack est maintenant prét å l'emploi. Garantie De Satisfaction Du Produit Chez Extreme Max, nous sommes fiers de fabriquer des produits de qualité et souhaitons corriger toute erreur de notre part. Si vous n'étes pas satisfait å 100% du produit, pour quelque raison que ce soit, veuillez nous contacter.
  • Page 4 Includes: • Heavy Duty f 5000 Jack • Coussins de levage en caoutchouc •31 "Hauteur de levage • Automobile Red Revétement en poudre durable • Grade 5 Hardware • Ascenseurs luge rapidement et uniformément Haut • 5-1/2 "Hauteur lorsque fermé •...
  • Page 5 Snowmobile LiftTM Wheel -naäuC7$ Installation Instructions 5800.1051 5800.1066 Includes: (8) - 5/16" by 3/4" Bolts - Front Power Wheels (8) - 5/16" Nyloc Nuts - Rear Brackets (2) - 7/16" x 4-1/2" Bolt - Instruction Sheet (6) - 7/16" Flat Washers - 3/8"...
  • Page 6 Snowmobile LiftTM Wheel -naäuC7$ Instructions d'installation 5800.1051 5800.1066 Includes: (8) - 5/16" x 3/4" boulons - Roulettes avant - 5/16" Nuts Nylstop - Supports arriére (2) - 7/16" x 4-1/2" boulon - Feuille d'instruction (6) - 7/16" Rondelles Plates - 3/8" x 3"...

Ce manuel est également adapté pour:

5800.1066