Technical Specifications - Hollywog WiTouch Manuel D'utilisation

1. Slowly peel the gel pad away from the black electrode area of the Hollywog WiTouch device. Be sure to remove all gel
residues from the electrode area.
2. Remove two (2) gel pads from the package and separate the pads at the perforation in the liner.
3. Remove the blue liners from one (1) gel pad by peeling away the folded edges of the liners. Discard the blue liners. DO NOT
remove the green protective liner at this time.
4. Align the shape of one (1) gel pad to match the shape of the black electrode area. Apply the gel pad to the black electrode
area, firmly pressing the gel onto the electrode. Press across the entire surface of the gel pad to ensure good adhesion.
5. Repeat step 3 and 4 for the second gel pad and electrode area.
6. Follow instructions for operation or storage of your Hollywog WiTouch
MAINTAIN your Hollywog WiTouch
• The Hollywog WiTouch LED indicator will alert when batteries require replacement:
1. Hollywog WiTouch device:
• When pressing ON/OFF button to turn on device: LED indicator blinks yellow every two (2) seconds when the device is ON.
• During stimulation treatment: LED indicator will blink yellow rapidly during the treatment.
2. Hollywog WiTouch remote control: LED indicator blinks yellow once when the START/STOP button is pressed.
• Return the Hollywog WiTouch to its storage box when not in use to ensure the device is protected during storage and
transport.
• The Hollywog WiTouch should be operated, transported and stored at temperatures between 50° F and 104° F (10° C
and 40° C), with relative humidity between 30% - 85%. All values have +/- 10% tolerance.
• Consult your local authorities for proper battery disposal.
• If the Hollywog WiTouch is not working properly, stop using immediately and contact Hollywog Customer Service.
• Do not disassemble or modify this device.
CLEAN your Hollywog WiTouch
Hollywog WiTouch Electrodes are single person use. Use a damp cloth and mild soap to gently wipe clean. Remove any soap residue
from cleaning. Damage to the device and/or remote control will occur if submerged in water or other liquids. WiTouch is manufactured
with water detection technology to detect exposure to water that may cause damage to the electronics and void the product warranty.

TECHNICAL SPECIFICATIONS

Channels: Single channel
Waveform: Asymmetric biphasic square pulse.
Pulse Amplitude: 0 ~110 mA = 0 ~ 55 volts, adjustable (at 500 ohm load)
Pulse Frequency: (Hz) 5-120
Pulse Width: (μs) 120 - 240
Timer Control: (mins) 30
Power Supply:
Device: Two (2) AAA batteries (Internally Powered)
Remote Control: One (1) CR2032 Lithium battery (Internally Powered)
Size (D x W x H): 0.7" x 7.5" x 3.5" (18 mm x 191 mm x 90 mm)
Weight (including battery): 4.8 oz (136 g)
Safety Standards: IEC/EN/UL 60601-1, IEC/EN 60601-1-2, IEC 60601-2-10, CAN/CSA C22.2 No. 601.1, EN 300200 / EN 301498-3
Made in USA
LED Indicator Guide
Event
Low battery - device
Low battery - remote control
Device transition from OFF to ON
Device transition from ON to OFF
Device transition from ON to START
STIMULATION mode
On remote control, press of
START/STOP TREATMENT button to
either START or STOP treatment
Device at maximum intensity and
+/- button pressed on remote or device
Remote control communication error
European Authorized Representative:
LED Color LED Sequence
One (1) blink every two (2)
Yellow
seconds when the device is ON.
Rapid blinking during the
stimulation treatment.
Yellow
One (1) blink every time the
START/STOP button is pressed.
One (1) blink every two (2)
Green
seconds.
None Green blinking stops.
Green Rapid blinking during treatment.
Green One (1) blink when START/STOP
button is pressed.
Two (2) blinks each time button
Yellow
is pressed.
Yellow
One (1) rapid blink, followed by
two (2) rapid blinks.
MDSS GmbH
Schiffgraben 41
0120
30175 Hannover, Germany
Limitations of Use and Storage
Atmospheric
Pressure Limitations
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
RF: 2.4GHz transceiver
Device:
Remote Control:
European
Conformity
30%
Temperature Humidity Limitations
Limitations
FCC ID: N8L-HWOGTENS11
IC: 10346A-HWOGTENS11
FCC ID: N8L-HWOGTENS12
IC: 10346A-HWOGTENS12
European
Directive
2002/96/EC
85%