Victor VLINK V450 Guide De Démarrage

VICTOR
VI-INK
START-UP GUIDE
Latch
Trap
Lid
Bait Cup
Kill
Chamber
Power
Outer Case
Pak
Battery
Compartment
Victor'V INC Mouse TrapModel: V450 1Victors VLINCRat T rapModel: V460
: FCC thisdevicecomplies withpart 15of thefcc rules. O perationis subjectto thefollowingtwo
conditions: ( l) thisdevicemaynotcauseharmfulinterference, and(2)thisdevicemustaccept
anyinterference received, i ncludinginterference that maycauseundesired operation.
Warning: C hanges o r modifications to thisdevicenotexpressly approved byWoodstream
Corporation couldvoidtheuser'sauthorityto operatetheequipment.
Note:Thisequipment h as beentestedandfoundto complywiththe limitsfor aClassBdigital
device, p ursuant t o Part15of the FCC Rules. T heselimitsaredesigned to providereasonable
protectionagainstharmfulinterference in aresidential i nstallation. Thisequipment g enerates,
uses,andcan radiateradiofrequency energyand,if notinstalledandusedinaccordance with
theinstructions, maycauseharmfulinterference to radiocommunicatiow However, thereis
no guarantee that interference willnotoccurin a particular i nstallation. I f thisequipment d oes
causeharmfulinterference to radioortelevision reception, w hichcanbe determinedby
turningthe equipment o ff andon,the userisencouraged to try to correctthe interference by
oneormoreof thefollowingmeasures:
• Reorient o r relocatethereceiving antenna.
• Increase the separation betweenthe equipment a ndreceiver.
•Connecttheequipmentinto anoutlet on acircuitdifferentfrom thatto whichthe
receiver is connected
•Consultthe dealeror an experienced radio/TVtechnicianfor help.
'C:Thisdevicecomplies with ndustryCanada's licence-exempt RSSs Operationis subjectto the
followingtwo conditions: ( l) Thisdevicemaynot causeinterference; a nd(2)Thisdevicemust
acceptanyinterference, i ncluding interference that maycauseundesired operationof the device.
RFExposure:Thisequipmentcomplies with FCC andICradiation exposurelimitsset forth for an
uncontrolled environment. Thisequipment s houldbeinstalledandoperatedwitha minimum
distance of 20cm betweentheradiatorandyour body.
WARNING:ElectricShockandSparkHazards. I gnition: Donot usenearunventedflammable
vapors, l iquids,orcombustible solids.Donotusein barns, s tables, o r similarwet ordusty
locations. H igh Voltage: Keepout of reachof childrenandpets.Useonly dryhandsor rubber
glovesto handle. P ower O FFandbait Donottouchmetalpla eswhendeviceis powered on.
Electromagnetic Waves:Keeppacemakers a ndlifesupportdevicesat leastone foot away.
Consult y our heartdoctorif you receivea shock Failure to readandheedall warningsand
directions maycauseelectric shock fire,orseriousinjury.Readandfollow all labelinstructions.
d Manufacture for:Woodstream Corporation 69 N.LocustStreet, L ititz,PA17543 • 800-800-1819
Beforeyou start: Confirmyou havea VI-INK account
and areable to successfullylog in at www.vlinkhq.com.
1. BATTERY
Open the outer case to access components.
When outer case lid is open, trap is disengaged.
2. Remove the
Aiiilii*
Bait
Trough
Power
Button
3.Slide out the power pak.
LED
Indicator
Light
LoRA
Button
4. Open the battery compartment on the bottom side of the
power pak and install the 4 "AA" lithium batteries (included).
5. Using a Philips head screw driver secure the battery
compartment lid to the power pak with the 7 screws
provided.
6. Reinstall the power pak.
7. Reinstall the kill chamber.
INSTALLATION
kill chamber.
2. BAITING
Option A
I. Remove bait cup.
2. Place your preferred solid bait in the bait trough located on
the top side of the kill chamber.
3. Replace bait cup.
Option B
1.Open bait cup and insert sticky or liquid bait into designated
bait area.
2. Replace bait cup.
3. CONNECTING
Plug in the VLINKTM hub.
If you are planning to use your local network, plug
your ethernet cable into the ethernet
For all other hub instructions, refer to the online setup
guide at www.vlinkhq.com/instructions.
4. DOWNLOAD THE APP
1.Download the VLINKTN app from the Apple or Google PlayStore.
DownlOad on the GET IT ON
App Store Google Play
2. Launch the app and follow the on-screen instructions to
connect your trap to the app.
5. SET TRAP
I. Once your trap has successfully connected, close the
lid-and the trap is set!
2. Place traps indoors or outdoors.
After every 20-25 kills, thoroughly clean the metal plates inside the kill chamber
with soapy water and a non-metallic brush, sponge, or scouring pad to maintain
trap effectiveness. It is also recommended that the kill chamber be wiped down
with a damp cloth after each kill to remove any debris.
port.