LiftMaster 365LM Guide Rapide

Life Maseer
This productshould be used only in connection
with garage door openers equipped with
photo-eyesafety sensors.If your garagedoor
STOP
opener doesnot have photo-eyesafety sensors,
you should considera replacementgaragedoor
opener. Please go to www.liftmaster.com to find
a local LiftMaster
INSTALLATION
1. Disconnect power to the garage door opener.
2. OPEN RECEIVER: Insert a small screwdriver
panel as shown. Twist up actuator cover (Figure 1).
3. CONNECT RECEIVER AND GARAGE DOOR OPENER: Remove 1/40
(6 mm) of insulation from each end of the 2-strand bell wire. Connect
one end of the wire to the receiver screw terminals (polarity is not
required). Route the wire along the channels and through the bottom
(Figure 2).
4. Connect the other end of the bell wire to the two opener terminals
labeled "2" (white) and "f" (red), "common" and "command" or the
terminals used for the push button control.
5. Use insulated staples to secure bell wire betweenthe receiver and the
garage door opener. The length of bell wire depends on where the
receiver will be installed. Replaceactuator cover.
6. Choose a 120 Vac polarized outlet for the receiver which is OUT OF
THE REACHOFCHILDREN.Plug receiver into selected outlet.
7. Reconnect power to the garage door opener.
8. Fully extend antennawire away from receiver for proper operation.
PROGRAMMING THE REMOTE CONTROL TO
THE RECEIVER
With Security+@,the code between the remote control and the receiver
changes with each use, accessing over 100 billion new codes.
You can activate your garage door opener with up to 8 SecuritY+@
remote controls and one SecuritY+@Keyless Entry.
1. Pry open the front panel of receiver case with a screwdriver.
Reconnect power to the garage door opener.
2. Press and release the "SMART"
"SMART" indicator light will glow steadily for 30 seconds.
3. Within 30 seconds, press and hold the button on the hand-held
remote control that you wish to operate your garage door.
The garage door opener will now operate when either the receiver
actuator or the remote control push button is pressed.
Repeat steps 2 and 3 for each remote control that will be used to operate
the garage door opener.
TO ERASE ALL REMOTE CONTROL CODES
Press and hold the "SMART" actuator on the receiver panel until the
indicator light turns off (about 6 seconds). All remote control codes are
now erased. Then follow the steps above to reprogram each remote
control.
dealer or call 1-800-528-9131.
in slot on receiver front
actuator on the receiver. The
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
MODEL365LM (315 MHZ) & 635LM (390 MHZ)
WARNING
To prevent possible SERIOUSINJURYor DEATHfrom electrocution:
• Be sure power is not connected BEFORE installing the receiver.
To prevent possible SERIOUSINJURYor DEATHfrom a moving gate
or garage door:
• ALWAYSkeep remote controls out of reach of children. NEVER
permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYSkeep gate or garage door in sight until completely closed.
NEVERpermit anyone to cross path of moving gate or door.
Figure 1
Actuator cover
Terminals
"SMART"
Indicator
Light
Antenna
Wire
SecurItY+@
Remote control
Select a
pusn button
NOTICE: T ocomply with FCC and or Industry Canada(IC) rules, adjustmentor modificationsof this
battery. THERE ARE NO O THER USER E SEÅVICEABL
Testedto comply with FCCStandards FORHOME OROFFICE USE.Operation is subjectto the
followingtwo conditions: ( 1) this devicemaynot causeharmfulinterference, and(2) this device
must acceptany interferencereceived,including interferencethat may causeundesiredoperation.
REPLACEMENT
Visor clip
3V2032 Lithium battery .
ACCESSORY REMOTE CONTROLS
Series 300.
Series 900.
1-800-528-9131
Figure 2
power Indicator Light
Bell Wire
cnannels
O
Connect Bell Wire
To Garage Door
opener Terminals
"SMART"
Actuator
Bell wre
Universal
Receiver
"SMART"
Actuator
Indicator
Light
the c ode setting or r eplacing
PARTS
. 29C137
IOA20
. Model 365LM
. Model 6351M
the