Sharper Image 60098-WHT Instructions D'assemblage
Chaise de massage lombaire active
Sommaire des Matières pour Sharper Image 60098-WHT
- Page 1 Active Lumbar Massage Chair Chaise de massage lombaire active Assembly Instructions Instructions d’assemblage Model / Modèle no. 60098-WHT...
- Page 2 Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: 1. Do not stand on the seat cushion. 2. Do not allow children to play on or near this product. 3.
- Page 3 PARTS/PIÈCES Star Base Gas Lift with Telescoping Cover Casters Seat Plate Base en étoile Roulettes Plaque de siège Vérin pneumatique avec couvercle Quantity/Quantité:1 Quantity/Quantité: 5 Quantity/Quantité: 1 télescopique Quantity/Quantité: 1 Left Arm Right Arm Seat Cushion Back Cushion Accoudoir de gauche Accoudoir de droite Coussin de siège Coussin de dossier...
- Page 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Étape 1 Placez la base en étoile (B) à l’envers et enfoncez les 5 roulettes (A) dans la base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top...
- Page 5 Step 3 Place the Back Cushion (G) between Arms (E1 & E2) and use 1-1/4” Small Screws (J) to fasten screws on both the arms and back cushion. Do not tighten the screws completely! Étape 3 Placez le coussin du dossier (G) entre les accoudoirs (E1 et E2) et utilisez les petites vis de 1-1/4 po (J) pour xer les vis des deux accoudoirs et du coussin du dossier.
- Page 6 Step 4 Place Seat Cushion (F) between Arms (E1 & E2), and use 1-1/4” Small Screws (J) to fasten screws on both the arms and seat cushion. Note: Tighten all the screws completely. Étape 4 Placez le coussin du siège (F) entre les accoudoirs (E1 et E2) et utilisez les petites vis de 1-1/4 po (J) pour xer les vis des deux accoudoirs et du coussin du siège.
- Page 7 Step 5 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using two 1-1/4” Big Screws (I) for the front holes of the Seat Plate (D) and two 1” Big Screws (H) for the rear holes of the Seat Plate (D) and tighten the screws using Allen Key (M).
- Page 8 Step 6 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F). Push down the key on the receivers to pull out the levers. Note: Fix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion. Étape 6 Insérez les leviers (D1 et D2) de la plaque du siège (D) aux récepteurs des leviers à...
- Page 9 Step 7 Pull down the metal plate of Back Cushion (G) and attach it over to the Seat Plate (D) by using 5/8” Knob (K). Tighten the knob. Étape 7 Tirez vers le bas la plaque de métal du coussin du dossier (G) et xez-la à la plaque du siège (D) en utilisant la bouton de 5/8 po (K). Serrez la bouton.
- Page 10 Step 8 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift (C) into the center hole of the Seat Plate (D). Push down rmly over the Gas Lift (C) until it is securely connected. Étape 8 Mettez le fauteuil assemblé...
-
Page 11: Function Instruction
Operating Instructions Mode d’emploi Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to nd the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. - Page 12 Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Pull up the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and push the lever to the down position.
- Page 13 Function Instruction - 4 Featuring Active Lumbar™ Technology: Patented technology allows the lumbar zone to ex, changing from full support to relaxed as you shift your sitting position from upright to reclined. The chair can be locked in the upright position using the tilt lockout for constant lumbar support while in a work posture.
- Page 14 Function Instruction - 5 360˚ Swivel: 360˚ seat swivel. Fonction - 5 Rotation De 360 Degrés : Rotation du siège de 360 degrés.
- Page 15 Function Instruction - 6 To Operate the Massager and Heating Function: Connect the adpter to the power cord of the chair. Insert the adapter into the electrical outlet. 1. Turn the unit on by pressing the power button once. The buttons Mode Intensity will glow white (except heat button).
- Page 16 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 17 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
-
Page 18: Garantie Limitée
Garantie limitée Les produits d’assise de True Innovations sont garantis contre tout défaut de matériau et de fabrication tant qu’ils restent la propriété de leur « acheteur initial ». Le terme « acheteur initial » se définit comme la partie ou l’entité ayant acheté le meuble True Innovations à...