Uline WINDPRO H-7041 Mode D'emploi
Liens rapides
π
H-7041, H-8546, H-8547
WINDPRO
HEAVY DUTY
®
SNAP EDGE SIGN
TOOL INCLUDED
Wrench
Frame x 1
NOTE: Remove washers and nuts before
assembling sign.
1.
Insert screws on bottom of frame through top of
base. (See Figure 1)
2. Place two-holed washer onto screws at bottom of
base. (See Figure 2)
PAGE 1 OF 6
1-800-295-5510
uline.com
PARTS
Base x 1
Two-holed Washer x 2
ASSEMBLY
3. Slide nuts onto screws on bottom of base. (See Figure 3)
4. Use wrench to tighten nuts around screws until snug
Figure 1
Figure 2
Pour le français, consulter les pages 5-6.
(Ships with base)
against washer. (See Figure 4)
CAUTION! Tighten carefully. When tightened too
much, the base can crack.
Para Español, vea páginas 3-4.
Nut x 4
(Ships attached to frame)
Figure 3
Figure 4
0425 IH-7041
Manuels Connexes pour Uline WINDPRO H-7041
Sommaire des Matières pour Uline WINDPRO H-7041
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. π H-7041, H-8546, H-8547 1-800-295-5510 uline.com WINDPRO HEAVY DUTY ® SNAP EDGE SIGN TOOL INCLUDED Wrench PARTS Frame x 1 Base x 1 Two-holed Washer x 2 Nut x 4...
- Page 2 NOTE: Ensure plastic cover comes into contact with black gasket to create weatherproof seal. 2. Remove plastic cover. (See Figure 6) Figure 7 5. Flip snap edges to closed position. (See Figure 8) Figure 8 Figure 6 1-800-295-5510 uline.com PAGE 2 OF 6 0425 IH-7041...
- Page 3 π H-7041, H-8546, H-8547 800-295-5510 uline.mx WINDPRO LETRERO DE USO ® PESADO CON MOLDURAS ABATIBLES HERRAMIENTA INCLUIDA Llave PARTES 1 Marco 1 Base 2 Rondanas de Doble Orificio 4 Tuercas (Se envían con la base) (Se envían adjuntas al marco)
- Page 4 2. Retire la cubierta de plástico. (Vea Diagrama 6) Diagrama 7 5. Coloque las molduras abatibles en la posición de cerrado. (Vea Diagrama 8) Diagrama 8 Diagrama 6 800-295-5510 PAGE 4 OF 6 0425 IH-7041 uline.mx...
-
Page 5: Montage
π H-7041, H-8546, H-8547 1 800 295-5510 uline.ca WINDPRO – ENSEIGNE ROBUSTE AVEC BORDS À PRESSION OUTIL INCLUS Clé PIÈCES Cadre x 1 Base x 1 Rondelle à deux trous x 2 Écrou x 4 (livrée fixée à la base) (livré... - Page 6 étanche. 2. Enlevez la couverture en plastique. (Voir Figure 6) Figure 7 5. Refermez les bords à pression. (Voir Figure 8) Figure 8 Figure 6 1 800 295-5510 PAGE 6 OF 6 0425 IH-7041 uline.ca...