Heidolph LABOROTA 20 control automatic Serie Manuels

Manuels et Guides d'utilisation pour Heidolph LABOROTA 20 control automatic Serie. Nous avons 1 Heidolph LABOROTA 20 control automatic Serie manuel disponible en téléchargement PDF gratuit: Manuel D'instructions

Heidolph LABOROTA 20 control automatic Serie Manuel D'instructions

Heidolph LABOROTA 20 control automatic Serie Manuel D'instructions (190 pages)

Marque: Heidolph | Catégorie: Équipement industriel | Taille: 6 MB

Table des Matières

Deutsch

5
English

65
- Summary
  65
- Parts and Accessories Supplied
  68
- Scope of Supply
  68
- Accessories (Optional)
  69
- General
  69
- Safety Information
  70
- Laborota 20 Control Automatic, Specifications
  71
- General
  72
- Remarks about Distillation
  72
- Select Vacuum Control Mode
  72
- Solvent Data
  73
- Laboratory Set-Up
  75
- Set-Up
  76
- Install Vapor Tube and PTFE-Seal
  77
- Install Condensers and Expansion Vessel
  78
- Assembly of Screw Joint KS 64
  79
- Install Inlet Pipe with Valve and Screwed Cap
  79
- Connection of PTFE Tubing (G)
  80
- Electric Connection of Cut-Out Sensor
  80
- Inlet Tube
  80
- Venting Tube: Condensate Cooler - Glass Set
  80
- Connection of Vacuum and Cooling Water Tubing
  81
- Connection Scheme Vacuum and Cooling Water
  83
- Electric Wiring between Automatic Module and Vacuum Pump
  83
- Glass-Set -A Automatic II 15-300-006-32
  84
- Automatic Distillation, Function Principle
  85
- Working with the Laborota 20 Control
  85
- Control Panel
  87
- Heating Bath Lift
  87
- Master Switch / EMERGENCY-CUT-OUT
  87
- Speed Setting
  88
- Heater
  89
- Select Vacuum Control Mode
  89
- P Const Vacuum Control Mode
  90
- T Auto Vacuum Control Mode
  90
- Calibrate Vacuum Pressure Sensor
  92
- Auto Start Stop
  94
- Safety Cut-Out in an Overpressure Situation
  95
- Timer
  95
- Safety Cut-Off in Case of a Defect in the Vacuum System
  97
- Safety Functions
  100
- Timer and Ramp-Function
  100
- Set Ramp Values
  101
- Delete Ramp
  105
- Discontinue Ramp Function
  105
- Display Ramp Values
  105
- Edit Ramp Values
  105
- Start Ramp Function
  105
- Automatic Module Functions
  106
- Fill Evaporator Flask
  108
- Distillation Cycle
  110
- End of Distillation
  110
- End of Product Metering
  110
- Flush Vacuum Pump
  110
- Connect Interface
  111
- Cut-Out-Sensor
  111
- Interface
  111
- Interface Parameters
  111
- RS 232 Interface
  111
- RS 232 Interface Commands
  112
- Drive Lock
  113
- Functions and Handling
  113
- Protective Enclosure
  113
- Tightening of Evaporator Flask
  113
- Flask Supports
  114
- Automatic Water Refill (Water Bath Model Only)
  115
- Vacuum and Water Distribution
  116
- Pt100 Temperature Sensor, Chiller
  117
- Condensate Drain (Water Bath Only)
  118
- Drain Heating Bath (Water Bath Only)
  118
- Fill Heating Bath (Water Bath Only)
  118
- Heating Bath Function and Handling
  118
- Heating Bath over Temperature Protection
  118
- Options
  119
- Temperature Sensor for Vapor
  119
- Cleaning & Servicing
  120
- Temperature Sensor for T Auto Vacuum Mode
  120
- Disposal
  121
- Troubleshooting
  121
- Uninstall, Forward & Store
  121
- Warranty, Liability & Copyright
  122
- Questions / Repair Work
  123
- Ce-Declaration of Conformity
  124
Français

125

Produits Connexes

Heidolph Catégories

Équipement de laboratoire Unités de contrôle Pompes

Climatiseurs

Climatiseurs Équipement industriel

Plus Manuels Heidolph