Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
POOL FILTER SYSTEM - TYPE S, TYPE T SERIES
6
SIGNS STICKED ON THE EQUIPMENT
The following signs are used inside the handbook and
on the machineries :
SYMBOL
EXPLANATION
Generic danger
Compulsory to protect
the respiratory tract
Access prohibited to
people not authorized
Compulsory to protect
hands with gloves
Compulsory to consult
the handbook
Compulsory to remove the
electrical connections for
the maintenance
7
TRANSPORT AND INTERNAL MOVING
The following specifications are to be considered:
It is recommended the use of qualified and specialized
staff to move, transport and install the equipment.
Moving should be executed by lifting the equipment
according to the following specifications:
by the edge with open lid;
☞
by the base;
☞
For short moving it is possible to use a fork lift
and/or manual trolley.
ATTENTION:
Carry out all the operations with caution
AND RISE THE EQUIPMENT BY FOLLOWING
THE INDICATED ZONE
ATTENTION:
It is necessary to follow the instructions reported
in this handbook to rise and to move the equipment.
6
WWW.NORSUP.EU
8
INSTALLATION
8.1
NORMAL WORKING
Connection should be executed by authorized and
qualified staff. Equipment's connection should be
linked to the pool system circuit. Connection should
be done by using threaded pipes union which are
included in the equipment, the thread and the
diameter are indicated in the components card.
Pipe union exit , included in the equipment, should be
connected by a glued smooth pipe (PVC) During the
normal working, the equipment should be placed in a
covered and dry area protected from the direct sunlight
irradiation and from heat.
For proper working conditions, the water temperature
should range between +5°C and +40°C. The filter has
a flow stream direction – which should be respected
– these are indicated by the arrows situated near
the pipe unions.
8.2 STORAGE
During an eventual storage the equipment should
be kept in a covered and dry place. The equipment
should be protected from eventual water sprinklings,
dust, humidity, collision or accidental damages.
Advisable room temperature should be included
between 0°C and +50°C.
8.3 STARTING
Check carefully that the components aren't damaged
because of transport collisions . If any part is damaged
or it is not in keeping with the original condition of supply-
ing, don't make the system work and provide for the
reparation or for the substitution at the assistance centre.
Check that all the filter connection pipes and the valves
are closed.
8.4 REFILLING
Refill the filter by putting in the filtering material from
the hole lid.
The Filter media sand used must have the following
characteristics:
FILTER MEDIA
GRANULOMETRY
0,4 ÷ 0,8 mm
QUARTZ SAND and
1 ÷ 2 mm
MILLED QUARTZ
1 ÷ 3 mm
3 ÷ 6 mm
ZEOLITE
1 ÷ 2,5 mm
2,5 ÷ 5 mm
DIATOMACEOUS
-
ANTHRACITE
0,8 ÷ 1,8 mm
ACTIVATED CARBON
-
Alterations which serve the technological progress as well as errors excepted!
POOL FILTER SYSTEM - TYPE S, TYPE T SERIES
ATTENTION:
Before refilling close the access hole of the
centre manifold pipe which is placed just under
lid. Remove the gasket from the filter's entry.
FILTER MODEL
MATERIAL QUANTITY
6 m3/h
75 Kg
10 m3/h
100 Kg
14 m3/h
150 Kg
22 m3/h
250 Kg
35 m3/h
550 Kg
ATTENTION:
At the end of the refill remove the closure
used for the manifold pipe which is placed
under the lid.
Afterwards fill the sand filter with water.
The refill should be done slowly by letting the water
flow in every interstices inside the filtering material.
Refill should be done until the water level overflows
the filter's edge.
ATTENTION:
Check that the spreading of the water in excess
doesn't cause damages and that there aren't any
nearby voltage and/or electric component parts
present were the excess water could be in
contact with.
8.5 FILTER CLOSING
•
Close the filter by the lid, the gasket, the clamp, the
screws and the nuts included in the equipment
•
Verify that the contact surfaces are clean and
eventually remove the dirt or the residual
filtering material;
•
Place the gasket on the filter.
•
Assemble the pressure gauge on the lid in the
proper hole (by the threaded hole or by the
proper back nut and O-ring);
•
Place the lid
•
Put the clamp to close the lid and the filter top
•
Place the 2 nuts in the clamp
•
Close the clamp using the screws, until the two
side are coincident. Do not over-screw!
8.6 STARTING
Open slowly the valves situated on the connection
pipe. Check that there are no water leaks.
Alterations which serve the technological progress as well as errors excepted!
ATTENTION:
In case of water leaks, close immediately the
filter valves and proceed with an examination
of the system.
8.7 WORKING
The equipment carries out the filtration of the water
according to what is described in this handbook. For a
good performance of the filter and for a good manage-
ment of the system connected to it, there are further
functions that should be considered and suggested.
By a different set up of the multi-port valve connected
to the filter (when models are included) it is possible
to carry out these other functions.
A 6 way valve has the following main working positions:
1
filtration
4
waste
2
backwash
5
circulation
3
rinsing
6
lock
The operating conditions of each position are described
in detail hereafter.
ATTENTION:
The selection with the
multiport valve level
should be done ONLY
WHEN THE SYSTEM IS
SWITCHED OFF AND
NOT IN USE!
8.8 FILTRATION
It is the normal position of exercise, it carries out the
filtration of the treated water from the entry to the exit.
8.9 BACKWASH
It is used for cleaning the filter media present in the
filter. This operation removes any suspended matter
caught by the filter media during normal exercise.
8.10 RINSING
it should be done after the backwash in order to
remove eventual impurities inside the valve.
8.11 WASTE
It allows water to flow straight to the waste (ex.
emptying the pool)
8.12 CIRCULATION
It allows the system to operate without the filter.
water is by-passed straight to the exit.
ORIGINAL MANUAL NORSUP
EN
DE
FR
7
Publicité
Table des Matières
