Relax LAGO Instructions De Montage page 4

Dear Customer,
We would firstly like to thank you for your trust and for purchasing this shower tray.
Please take a few minutes to read this manual before proceeding with the installation. The entire content is based on the most recent product information available at
the time of publication. We reserve the right to make changes to the product features, packaging or availability at any time and without prior notice.
BEFORE STARTING:
Observe all of the local hydraulic and building regulations.
The following instructions are to be followed by qualified personnel with the technical background and experience needed to manage the product safely.
This shower tray should only be used in domestic environments at room temperature.
The Manufacturer shall not be held responsible and the warranty shall no longer be valid in case of improper use.
Open the package and inspect the shower tray for damage.
Before installing the product, use a metallic bar or ruler to make sure the product has not warped due to improper storage. In case of improper installation, warranty
will decay. In case of installation of a warped/deformed product, warranty will decay. A 2 mm distortion per linear metre is within the tolerances of manufacture and is
therefore not to be considered a defect.
Place the shower tray back in the carton until it is installed.
Before installing, check access to the final hydraulic connections.
To prevent water stagnation, the shower jet must fall entirely and exactly within the shower tray, preferably above the drain (and never above the flat standing/walk-in
area). Warranty will decay in case of improper installation.
PREPARING THE LOCATION:
Make sure the floor and the supporting surfaces are flat and leveled. Drill a hole that is wide enough to contain the appropriate drainage kit needed for the drainage
system. The hole must be appropriately located and while keeping the position and size of the shower tray in mind.
PREPARING THE SHOWER TRAY
Extract the shower tray from the packaging, which should be disposed of in accordance with the local regulations in force.
Install the drainage kit on the shower tray as indicated by the Manufacturer.
Position the shower tray where it shall be installed (raised by means of wooden blocks) and fasten all the hydraulic connections of the drainage system.
Open the faucets and let the water run inside the shower tray. Check all the connections for possible leaks.
Place the shower tray on the floor and make sure it is perfectly flat. Seal the entire perimeter of the shower tray with acetic silicone. If the shower tray is slightly
above the floor, or semi-embedded, leave 2-3 mm of space around the entire perimeter (which must be sealed with acetic silicone); as to make room for the thermal
expansion of the material.
Let the silicone dry for at least 24 hours before using the shower tray (or before mounting any shower walls).
INSTRUCTIONS FOR USE:
This shower tray cannot be used autonomously by people with reduced motor skills, or with sensory and/or cognitive impairments (including children), or by anyone
lacking the necessary know-how needed.
Make sure children are supervised by a person in charge of their safety when using this shower tray.
This shower tray was designed for domestic use, or similar, and it must only be installed and used at room temperature.
It is dangerous to use the shower tray in the vicinity or while using electrical appliances (radios, hair dryers etc.).
Pay special attention when using the shower alone: standing under running hot water for a long time could cause nausea, dizziness and lack of consciousness.
We do not recommend using the shower after taking medicines or any substance that could cause drowsiness or that could affect blood pressure.
Do not use water at temperatures above 40° C.
When the surface of the shower tray is wet, the degree of slipperiness increases, especially if shampoos, soaps and oils are used. This shower tray could be slippery
during its use.
Do not clean using aggressive chemical agents, such as acetone, thinners, strong acids (muriatic acid etc.) or strong bases (caustic soda etc.), nor industrial detergents
or paint solvents. For more information, please refer to the cure and maintenance instructions that are supplied with the product. Do not use metal scrapers, iron
brushes or other domestic metal tools to remove stains, paints, plaster or other. Some substances, such as ink, cosmetics and dyes, can stain the material if they are
in contact with the surface for too long; the same thing can happen with lit cigarettes.
We do not recommend using this product at water temperatures above 55°C (130° F). The Manufacturer shall not be liable for any damages that may result from the
improper use of the product.
WARRANTY:
This product is regulated under the National and European regulations relating to the sale of consumer goods.
The warranty is valid when a lack of conformity is noticed within two years from the time the product was delivered. This warranty does not affect the legal rights of the
Buyer. Check if there are any additional commercial warranties for this product.
The WARRANTY is valid whenever:
• Installation was performed appropriately, with walls, shower tray, well-aligned walls and leveled floors.
• The product was checked before installation.
• The installation, as made, was checked to make sure there were no water leaks.
• Product maintenance and cleaning are carried out according to the instructions reported in the Cure and Maintenance Manual.
The WARRANTY is not valid whenever:
• The instructions for use and installation reported herein were not observed.
• The Installer/User changed or customized the product without the manufacturer's authorization.
• Accidental damages occur as a result of collisions or improper use.
• The wear and tear of the product occurs normally.
• Damages are caused by disasters, such as fires or natural disasters, including floods, earthquakes, etc.
4
INSTRUCTIONS FOR USE AND INSTALLATION
OF THE SHOWER TRAY