Error Messages; Technical Data - CTC CLATRONIC EKI 3343 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
Automatic shut-off
The hot plate turns off automatically after 120 minutes, if no
input was given over the operator control panel during this
time. This switching serves as security for you.
Switching off
Press the ON/STANDBY button (5).
NOTE:
The hot plate is reset from its operational state to standby
mode. The fan may continue to run for a period of time.
A signal sounds and the indicator lamp on the ON/
STANDBY button (5) flashes.
As long as the hot plate is still hot, a „H" flashes on the
display.
Pull the plug.
Let the device cool down, before you put it away.
Pan recognition
The device has a pot recognition function. After the pot has
been taken from the hob, it switches back to the standby mode.
In this context, please pay attention to the following:
WARNING:
• After use, the hot plate is to be switched off by means of
its regulation and control devices (ON/STANDBY button)
and not just by pan recognition.
• Hazard of burns! Because of the heat radiated during
cooking, dangerously high temperatures may occur at the
cooking zone after the cooking cycle.
Cleaning
AVVISO:
Always remove the mains lead before cleaning!
Wait until the machine has cooled down completely.
Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might result
in an electric shock or fire.
CAUTION:
Do not use a wire brush or any abrasive items.
Do not use any acidic or abrasive detergents.
Ceramic Hob
Clean the surface from food remains when it's still warm
using a moist cloth or tissue.
Wash the hob using a soft sponge and some water, then
wipe dry with a soft cloth.
Cleaning agent for glass-ceramics surfaces: In case of
stubborn, baked-in remains, use suitable cleaning products
available at special departments of department stores.
Housing
Clean the housing after use using a slightly moist cloth.
Make sure that no fluid matter gets into any of the openings
of the housing. This might damage the device or result in an
electric shock.
05-EKI 3343.indd 31
Troubleshooting
• Device does not function, no indication on the display.
Remedy:
Check the mains connection.
• T here is a sound after I have selected a cooking
function and switched the device on.
Possible cause:
You put no or an unsuitable pot on the hob.
NOTE:
For reasons of safety, the device automatically switches to
the standby mode after a few seconds.
Remedy:
Put a pot on the hob that is suitable for induction hobs.
• T he hob suddenly switches off during operation.
Possible cause:
The overheating protection (cutout switch) has been
activated.
Remedy:
Pull the plug and let the device cool down for about 20 min.
Then start operating the device again.
Further cause:
The ventilation slots are obstructed.
Remedy:
Free the ventilation slots from any obstructions.
Further cause:
The hot plate was automatically switched off after 120
minutes.

Error messages

During the operation the display shows the following security
instructions:
Security
instruction
E1,E2,
In this case, there is a problem with the
E4, E5,
electronic control.
Eb, EC
E3, E6
Overheating. See below remedy of the fault.
E7, E8
Overvoltage or undervoltage
Check the power supply system!

Technical Data

Model: ..............................................................................EKI 3343
Power supply: ...............................................220–240 V, 50/60 Hz
Power consumption: ..........................................................2000 W
Protection class: .......................................................................... II
Net weight: ........................................................................2,33 kg
31
25.11.2009 14:25:48 Uhr

Publicité

Table des Matières
loading

Table des Matières