USING THE USB PORT
The USB port provides up to 2A
at 5V DC.
1. Ensure the battery clamps are
securely clipped on the storage
holders.
2. Turn the jump starter ON.
3. Plug your device into the USB port.
4. Turn on the USB device.
5. When finished using the USB port,
turn the switch to the OFF position.
6. Charge the jump starter.
USING THE WORK LIGHT
The work light is controlled by a sliding
ON/OFF switch located on the front of the
jump starter. Make sure the lamp is turned
OFF when the unit is being recharged or
stored.
Position the jump starter on a flat, stable
surface near the intended work area.
Ensure the battery clamps are securely
clipped on the storage holders.
POWERING A 12V DC DEVICE
The jump starter is a power source for all
12V DC accessories that are equipped
with a 12V accessory plug. Use it for power
outages and on fishing or camping trips.
NOTE: Do not power a 12V device
with the jump starter while charging the
internal battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC
power outlet on the jump starter.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the jump starter
to run appliances that draw more than
20A DC.
NOTE: Extended operation of a 12V
DC device may result in excessive
battery drain. Recharge the jump starter
immediately after unplugging the 12V
DC device.
Estimated run-times
APPLIANCE TYPE
Cell phone
Fluorescent light
Radios, fans
Depth finder
Camcorder
Electrical tool
Electric cooler
Car vacuum, air compressor 80 watts
NOTE: Actual time may vary. Times are based
on the internal battery being fully charged.
USING THE AIR COMPRESSOR
(Model FR01240 only)
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
NOTE: Wrap cleats are provided for
convenient storage of the air compressor
hose. Wrap the hose around these cleats
when the hose is not in use.
1. Remove the air compressor hose from
the storage cleats.
2. Connect the adapter to the valve
stem by threading it onto the end. If
necessary, use one of the additional
adaptors.
3. Press the air compressor power
switch to turn ON and inflate to the
desired pressure or fullness (refer to
the gauge next to the switch).
NOTE: To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off,
wait a few minutes and it will automatically
restart when the compressor cools.
4. When the desired pressure is
reached, press the air compressor
power switch to turn OFF and remove
the connector from the valve stem.
5. Allow unit to cool.
6. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air
compressor gauge to ensure the proper
pressure has been reached. Do not overinflate.
• 8 •
EST
FR01239
FR01240
WATTAGE
4 watts
19 hrs
34 hrs
4 watts
21 hrs
34 hrs
9 watts
9.3 hrs
14 hrs
9 watts
9.3 hrs
14 hrs
15 watts
5.6 hrs
7 hrs
24 watts
3.5 hrs
5 hrs
48 watts
1.8 hrs
2 hours
1.1 hrs
1.8 hrs
6-24 minutes
1-3 minutes
30 seconds