Publicité
Les langues disponibles
Les langues disponibles
MODEL: PBR50Q
Make sure the hose is free of obstructions
●
or snags. Entangled or snarled hoses can
cause loss of balance or footing and may
become damaged, resulting in possible injury.
●
Do not overreach. Keep proper footing and
balance at all times.
Proper footing and
balance enables better control of the tool in
unexpected situations.
●
Do not attach the hose or tool to your body.
Attach the hose to the structure to reduce the
risk of loss of balance if the hose shifts.
●
Always assume that the tool contains
fasteners. Do not point the tool toward
yourself or anyone whether it contains
fasteners or not.
●
Wash hands after handling.
This product or
its power cord may contain chemicals known to
the State of California to cause cancer and birth
defects or other reproductive harm.
TOOL USE AND CARE
●
Know this tool. Read manual carefully, learn
its applications and limitations, as well as the
specific potential hazards related to this tool.
●
Use only fasteners that are recommended
for your models.
Do not use the wrong
fasteners or load the fasteners incorrectly.
●
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool's
operation.
If damaged, have the tool serviced
before using. Many accidents are caused by
poorly maintained tools.
●
Maintain tools with care.
Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
●
Store tools out of the reach of children and
other untrained people.
Tools are dangerous
in the hands of untrained users.
●
Check operation of the tool before use.
not use the tool if the workpiece contact
mechanism is not working correctly as
accidental driving of a fastener may occur.
●
Do not use tool if trigger does not actuate
properly.
Any tool that cannot be controlled
with the trigger is dangerous and must be
repaired.
●
Do not force tool.
Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
●
Use clamps or another practical way to
secure and support the workpiece to a
stable platform.
Holding a tool by hand or
against the body is unstable and may lead to
loss of control.
04
.
HTTP://WWW FREEMANTOOLS COM
Keep the tool and its handle dry, clean and
●
free from oil and grease.
Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.
●
Do not use the tool as a hammer.
●
Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
●
Never use gasoline or other flammable
liquids to clean the tool.
Never use the tool in
the presence of flammable liquids or gases.
Vapors could ignite by a spark and cause an
explosion which will result in death or serious
personal injury.
●
Do not remove, tamper with, or otherwise
cause the trigger lock or trigger to become
inoperable.
Do not operate any tool which has
been modified in a like fashion. Death or
serious personal injury could result.
●
Do not touch the trigger unless driving
fasteners.
Never attach air line to tool or carry
tool while touching the trigger. The tool could
eject a fastener which will result in death or
serious personal injury. Also actuate the trigger
lock to the safe position when not in use.
●
Always fit tool with a fitting or hose
coupling on or near the tool in such a
manner that all compressed air in the tool is
discharged at the time the fitting or hose
Do not use a check
coupling is disconnected.
valve or any other fitting which allows air to
remain in the tool. Death or serious personal
injury could occur.
●
Never place hands or any other body parts
in the fastener discharge area of the tool.
The tool might eject a fastener and could result
in death or serious personal injury.
●
Never carry the tool by the air hose or pull
the hose to move the tool or a compressor.
Do
Keep hoses away from heat, oil and sharp
edges. Replace any hose that is damaged,
weak or worn. Personal injury or tool damage
could occur.
●
Always assume the tool contains fasteners.
Respect the tool as a working implement; no
horseplay.
●
Always keep others at a safe distance from
the work area in case of accidental
discharge of fasteners.
Do not point the tool
toward yourself or anyone whether it contains
fasteners or not. Accidental triggering of the tool
could result in death or serious personal injury.
.
1-888-669-5672
MODEL: PBR50Q
Do not drop or throw the tool.
Dropping or
●
throwing the tool can result in damage that will
make the tool unusable or unsafe. If the tool has
been dropped or thrown, examine the tool
closely for bent, cracked or broken parts and air
leaks. STOP and repair before using, or serious
injury could occur.
Avoid using the tool when the magazine is
●
empty.
Accelerated wear on the tool may
occur.
●
Clean and check all air supply hoses and
fittings before connecting the tool to an air
supply.
Replace any damaged or worn hoses
or fittings. Tool performance or durability may
be reduced.
●
Do not use th
e tool if it leaks air or does not
function properly.
●
Do not operate the tool if it does not contain
a legible warning label.
Always carry the tool by the handle. Never
●
carry the tool by the air hose.
TOOL SERVICE
●
Use only accessories that are identified by
the manufacturer for the specific tool model.
●
Use of unauthorized parts or failure to
follow maintenance instructions may create
a risk of injury.
●
Use only the lubricants supplied with the
tool or specified by the manufacturer.
●
Tool service must be performed only by
qualified repair personnel.
OPERATION
●
Do not drive fasteners near edge of material.
The workpiece may split causing the fastener or
ricochet, injuring you or people around.
●
Do not carry the tool from place to place
holding the trigger. Accidental discharge
could result.
Choice of triggering method is
important. Check manual for triggering options.
●
During normal use the tool will recoil
immediately after driving a fastener.
This is
a normal function of the tool. Do not attempt to
prevent the recoil by holding the tool against the
work. Restriction to the recoil can result in a
second fastener being driven from the tool. Grip
the handle firmly and let the tool do the work.
Failure to heed this warning can result in serious
personal injury.
Do not drive fasteners on top of other
●
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
.
HTTP://WWW FREEMANTOOLS COM
●
Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
●
Always handle the tool with care:
◆Respect the tool as a working implement.
◆Never engage in horseplay.
◆Never pull the trigger unless nose is directed
toward the work.
◆ Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
●
The connector on the tool must not hold
pressure when air supply is disconnected.
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus
will be able to drive a fastener even after the air
line is disconnected, possibly causing injury.
●
Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal
injury.
●
Use only a pressure-regulated compressed
air source to limit the air pressure supplied
to the tool.
The regulated pressure must not
exceed 100 psi. If the regulator fails, the
pressure delivered to the tool must not exceed
200 psi. The tool could explode which will cause
death or serious personal injury.
●
Always disconnect air resource:
◆Before unloading or making adjustments.
◆When maintaining the tool.
◆When clearing a jam.
◆When touching the safety yoke.
◆When tool is not in use.
◆When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
LOADING TOOL
●
Do not load the tool with fasteners when
any one of the operating controls is
activated.
●
Never place a hand or any part of body in
fastener discharge area of tool.
●
Never point tool at anyone.
●
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
.
1-888-669-5672
If
Use
05
Publicité
