Télécharger Imprimer la page

Makita DKT360Z Manuel D'instructions page 10

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
Appliance / battery protection
system
The appliance and battery are equipped with the protec-
tion system. This system automatically cuts off power
to the motor to extend appliance and battery life. The
appliance will automatically stop during operation if the
appliance or battery is placed under one of the following
conditions.
Overload protection : When the appliance or
battery is operated in a manner that causes it to
draw an abnormally high current, the appliance
automatically stops without any indication. In
this situation, turn the appliance off and stop the
application that caused the appliance to become
overloaded. Then turn the appliance on to restart.
Overheat protection : When the appliance or
battery is overheated, the appliance automatically
stops. Let the appliance cool down before turning
it on again.
Overdischarge protection : When the battery
capacity becomes low, the appliance stops auto-
matically. If the appliance does not operate even
when the switches are operated, remove the
battery cartridge from the appliance and charge it.
Protections against other causes
Protection system is also designed for other causes that
could damage the appliance and allows the appliance to
stop automatically. Take all the following steps to clear
the causes, when the appliance has been brought to a
temporary halt or stop in operation.
1.
Turn the appliance off, and then turn it on again to
restart.
2.
Charge the battery(ies) or replace it/them with
recharged battery(ies).
3.
Let the appliance and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
Using appliance with cord
connected power source
Before using the cord connected power source, read
instructions and cautionary markings on it.
WARNING:
When using the appliance with
the cord connected power source, put the cord
connected power source on the stable surface.
This appliance is used in static position. Using the
cord connected power source which you carry on
your back may cause falling accident.
OPERATION
Preparation
When using the appliance for the first time, or after long
period of storage, perform the following steps.
1.
Remove all packing materials from the appliance.
2.
Clean the interior of the kettle and filter. There may
be dirt such as dust on them.
See the chapter "MAINTENANCE" for how to clean.
Boiling water
CAUTION:
Boil only water. Do not boil other
than water.
CAUTION:
Do not put the appliance on an
unstable place, a place where people often pass,
or a place where children can reach. Otherwise the
appliance may be accidentally tipped over and cause
an injury.
CAUTION:
When closing the lid, push the
lid securely and put the discharge lock button in
locked position. Otherwise burn injury may occur
when falling accident occurs.
1.
Open the lid while pushing both of the open-lid
buttons.
2.
Pour preferred amount of fresh tepid water into the
kettle. Then close the lid.
CAUTION:
Make sure the discharge lock
button is in locked position. Otherwise boiled water
may be spilled unintentionally and cause burn injury.
CAUTION:
Do not over fill water exceeding
the maximum line. Otherwise boiled water may be
ejected and cause burn injury.
NOTICE:
Prevent no-water burning, do not turn
on the appliance without water. Otherwise discolor-
ation or malfunction may occur.
► Fig.6
3.
Put the kettle onto the power supply stand.
► Fig.7
4.
Push the power switch.
The power switch lights up in orange with single beep
sound, then boiling starts.
► Fig.8: 1. Power switch
CAUTION:
Do not touch the steam. Risk of
burn injury.
► Fig.9
CAUTION: Do not touch around
the metal part located in the figure during boiling
or some time after boiling. Risk of burn injury.
► Fig.10: 1. Metal part that may extreme hot
10 ENGLISH
mark and

Publicité

loading

Ce manuel est également adapté pour:

Dkt360