Work Smart FL23591G Instructions De Montage

ÉTAPE 1 ÉTAPE 2
3
4
1
2
ÉTAPE 4 ÉTAPE 5
8
5
10
8
9
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste
et vous assurer que les quantités des pièces sont correctes.
ÉTAPE 1 Insérer les cinq roulettes (2) dans la base (1). Pousser fermement jusqu'à ce que les
roulettes (2) s'encliquettent. Insérer le vérin pneumatique (3) dans la Base (1).
ÉTAPE 2 Fixez la plaque du siège (4) au corps de chaise (5) avec la flèche vers l'avant de la chaise avec
quatre vis courte (7). SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (11).
ÉTAPE 3 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas. Ouvrir
le corps de chaise (5).
ÉTAPE 4 Enlever quatre vis longues (8) du corps de chaise (5).
ÉTAPE 5 Fixez les bras (6L et 6R) au corps de chaise (5) avec deux vis longue (9) pour chaque bras (6).
SERREZ TOUTES LES VIS AVEC LA CLÉ ALLEN (11). Couvrir les trous des bras (6R et 6L) avec une
couvertures en plastique (10) et deux bouchons en plastique (9) pour chaque bras (6).
ÉTAPE 6 Attacher le rabat arrière de la chaise.
ATTENTION : AVANT D'UTILISER LE FAUTEUIL, VOUS ASSURER D'AVOIR RESSERRÉ
COMPLÈTEMENT TOUTES LES VIS.
FL23591G
FAUTEUIL À DOSSIER HAUT
EN SIMILI-CUIR
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
7
5
ÉTAPE 6
10
6L
6R
9
8
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3. Vérin pneumatique . . . . . . . . . . . . . . . . . . .1
4. Plaque de siège . . . . . . . . . . . . . . . . . . . . . .1
5. Corps de chaise . . . . . . . . . . . . . . . . . . . . .1
6. Bras (6L et 6R) . . . . . . . . . . . . . . . . . . . . . .2
7. Vis courte . . . . . . . . . . . . . . . . . . . . . . . . . . .4
8. Vis longue . . . . . . . . . . . . . . . . . . . . . . . . . .4
9. Bouchons en plastique . . . . . . . . . . . . . . . .4
10. Couverture en plastique . . . . . . . . . . . . . .2
11. Clé Allen (non montré) . . . . . . . . . . . . . . . .1
5
3
1
WORK SMART LIMITED WARRANTY
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
QTÉ
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. The BC9601 is for persons weighing 300 lbs. or less. The BC9602 is for persons weighing 400 lbs. or less. The BC9603 is for persons weighing 500 lbs.
or less. EX1098, EC1283C & ECH12801 are for persons weighing 350 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse,
negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover
cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting
from use of this product. When usage is more than 40 hours per week, a two year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
© Office Star Products novembre 2017
FL23591G
MID BACK FAUX LEATHER CHAIR
ASSEMBLY INSTRUCTIONS
FEATURES
• HEIGHT ADJUSTMENT
To raise seat, remove pressure from seat and lift lever (1).
To lower seat height, sit on chair and lift lever (1).
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of the
tilting feature. Turn knob (2) clockwise to increase tension and
counter-clockwise to decrease or ease the tension. To lock,
return chair to the upright position and push lever (1) in.
To unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
WARNING
1. Use this product only one person at a time.
2
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.