Witter C44AU Instructions De Montage

Fitting
Instructions
MATERIALS
A 1 Cross Bar
D 1 Side Arm Right
E 1 Side Arm Left
F 6 M8 X 35 X 1.25 mm Bolts (10.9 grade), Lock washers and 6 flat washers (25 mm OD)
G 1 M10 X 35 X 1.50 mm Bolts, Lock washers and 1 Flat washers (25 mm OD)
H 2 M10 X 35 X 1.50 mm Bolts, 4 Flat washers (25 mm OD) and 2 Nyloc Nuts.
J 4 M12 Bolts caps
K 2 M8 X 45 X 1.25 mm Bolts, Lock washers and 2 flat washers (25 mm OD)
M 1 M10 X 50 X 1.50 mm Bolts, Lock washer and 1 Flat washer (25 mm OD)
N 1 ZEQ 5 Electrical plate angle bracket.
P 1 Z99 Flip up electrical kit.
Vehicles with self levelling C44
C44 Flange neck option – ZF2033. Note: This towbar must be used with either a Witter Tow ball (part number Z11) or Class
A50-1 or A50-X tow ball dimensionally Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
C44Q Detachable neck option – ZQ2070. Please refer to ZQ fitting instructions for installation
C44QF Detachable neck option – ZQF2070. Please refer to ZQF fitting instructions for installation
Recommended torque settings: Grade 8.8 bolts: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M16 - 214 Nm Grade 10.9:
M12 – 139Nm, M8 – 35 Nm.
FITTING
Bumper removal
1. Check to ensure that you have all the necessary parts. To remove bumper, open boot unclip inner boot linings to obtain
access to rear lights. Disconnect and remove rear light clusters: x1 plastic nut behind each light cluster. This will expose
1 torx screw hidden inside the rear wing between 2 plastic studs, remove on both sides.
2. Undo 4 upper torx screws on the outside of bumper, continuing with 2 arch screws and 1 tip screw each side. Fold back
inner arch cloth to expose 1 torx each side. For reversing sensors unplug the connection found under the offside rear.
3. Remove 4 screws under bumper and 1 nut. To remove bumper pull tips outwards this can be eased by sliding a screw
driver from the inner arch to release clip.
Fitment of Cross bar
4. Remove crash beam and retain for customer. Fit part (A) to the rear panel and finger tighten using fasteners (F).
5. Fit right side arm (D) using bolt (G) to outside chassis rail and allow to swivel. Note: Captive holes are covered in tape.
Rotate side arm up to part (A) end profiles and fix using fasteners (H).
6. Connect side arm (E) to cross bar (A) by fully threading bolts (K) rearward through the existing lower set of M8 holes.
7. Secure side arm (E) using bolt (M) to outside chassis rail. To improve access to mounting point cut cross into side cloth for
use of ratchet. Note: Bolt (M) is longer for the bush on the exhaust side.
8. Once all aligned tighten remaining bolts to their recommended torque
9. Refit bumper ensuring upper tips align, refit all the screws that were removed and ensure the reverse sensor plug is
reconnected.
10. Attach preferred neck and electrical plate bracket (ZEQ5) to the rearward bolt hole position. Attach the Z99 flip up kit and
as option cut bumper should the electrical socket require it. Fit Bolt Caps (J)
11. Fully tighten all remaining fixings to the recommended torque setting.
.
For CITROEN C5 TOURER 2008 –
Vehicles with self levelling
W0001C44AU-FIT$011005190000$Ä
W0001C44AU-FIT$011005190000
TOWBAR
C44AU for
C44
C44Q
C44QF